Delta D25886 User Manual Page 246
- Page / 339
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4. Motion Control Instructions
DVP-MC operating manual 4-205
Parameter
name
Explanation
Data
type
Available
device
C_Pos
The coordinate position of terminal
point of the added axis
REAL Constant, D
P_Pos
The coordinate position of terminal
point of the added axis
REAL Constant, D
Q_Pos
The coordinate position of terminal
point of the added axis
REAL Constant, D
I_Value
The corresponding X-axis coordinates
of the center of a circle
REAL Constant, D
J_Value
The corresponding Y-axis coordinates
of the center of a circle
REAL Constant, D
K_Value
The corresponding Z-axis coordinates
of the center of a circle
REAL Constant, D
T_Value The quantity of the full circle UINT Constant, D
Velocity The feed speed of the circular arc REAL Constant, D
Acceleration Acceleration REAL Constant, D
Deceleration Deceleration REAL Constant, D
GroupID
The number of the coordinate motion
instruction group, range: 0~7.
When the instruction is executed, the
group ID should be consistent with that
of DNC_Group.
UINT Constant, D
Done
When the execution of the instruction
is finished, “Done” is on; when
“Execute”
turns off, “Done” is reset.
BOOL M,Q
Error
If any error is detected, "Error" turns
on; when "Execute" turns off, "Error" is
reset.
BOOL M,Q
ErrorID Error code. Please refer to section 5.3. UINT D
Note:
1. The function of the instruction DNC_CW(IJK) (G2) and DNC_CCW(IJK) (G3) is same as that of G2
and G3 in G codes and the input parameters X_Pos~Deceleration in the instruction and the
parameters of X_, Y_, Z_, A_, B_, C_, P_, Q_, I_, J_, K_,T_, F_,E_,E_ in G2 and G3 have same
explanation. For more details on G2 and G3, please refer to section 4.8.3.5.
2. The state of axis related with the instruction is Standstill. After “DNC_Group” is executed, the
instruction just can be executed and its GroupID must be same as that of DNC_Group.
3. The instruction can be switched to absolute mode via DNC_Absolute (90). In absolute mode, the
terminal position of each axis is based on 0 unit.
4. The instruction can be switched to relative mode via DNC_Relative (91). In relative mode, the
terminal position of each axis is calculated as incremental value beginning from current position.
- DVP-MC Bus-Type 1
- Multi-Axis Motion Controller 1
- Operating Manual 1
- Content 2
- Overview of DVP10MC11T 7
- 2. System Function 10
- 3. System Installation 34
- 4.1. Instruction Table 42
- 4.2. Axis Status 46
- 4.3. Instruction Usage 47
- Instruction format 47
- Data type list 48
- 4.4.1. MC_MoveAbsolute 49
- Program Example (1) 52
- Program Example (2) 53
- 4.4.2. MC_MoveRelative 55
- 4.4.3. MC_MoveAdditive 59
- 4.4.4. MC_MoveSuperImposed 63
- 4.4.5. MC_MoveVelocity 68
- 4.4.6. MC_Stop 71
- 4.4.7. MC_PassiveHome 74
- Example 75
- 4.4.8. MC_Power 77
- 4.4.9. MC_Reset 78
- Exmaple: 79
- 4.4.10. MC_ReadStatus 80
- 4.4.12. MC_ReadAxisError 82
- 4.4.13. DMC_ReadParameter 83
- 4.4.14. DMC_WriteParameter 84
- 4.4.15. DMC_SetTorque 85
- Program Example 86
- 4.5.1. MC_CamTableSelect 87
- 4.5.2. MC_CamIn 88
- = 0, slave position is 101
- 0, slave offset = 0 102
- Master Positio 102
- offset = 40, slave position 103
- Electronic cam example: 104
- Position 105
- 4.5.3. MC_CamOut 107
- Program Example: 108
- 4.5.4. DMC_CamSet 110
- Acceleration 112
- 4.5.5. MC_GearIn 114
- . UINT D 115
- 4.5.7. MC_Phasing 118
- Sequence Diagram 120
- 4.5.8. DMC_CapturePosition 121
- 4.5.9. DMC_VirtualAxis 127
- 4.5.10. DMC_ExternalMaster 129
- 4.6. Logical Instruction 131
- 4.6.3. ADD_R 132
- 4.6.4. SUB 132
- 4.6.5. SUB_DI 133
- 4.6.6. SUB_R 133
- 4.6.7. MUL 134
- 4.6.8. MUL_DI 134
- 4.6.9. MUL_R 135
- 4.6.10. DIV 135
- 4.6.11. DIV_DI 136
- 4.6.12. DIV_R 136
- 4.6.13. AND 137
- 4.6.14. OR 137
- 4.6.15. XOR 138
- 4.6.16. NOT 138
- 4.6.17. CTU 139
- Program example: 140
- 4.6.18. CTD 141
- 4.6.19. CTUD 143
- 4.6.20. TON_s 145
- 4.6.21. TOF_s 147
- 4.6.22. TONR_s 149
- 4.6.23. TON_ms 151
- 4.6.24. TOF_ms 152
- 4.6.25. TONR_ms 153
- 4.6.26. CMP 154
- 4.6.27. CMP_DI 155
- 4.6.28. CMP_R 156
- 4.6.30. MOV_DI 158
- 4.6.31. MOV_R 158
- 4.6.34. MOVF_R 161
- Program example : 162
- 4.6.36. MOV_BW 163
- 4.6.38. ZCP 165
- 4.6.39. ZCP_DI 166
- 4.6.40. ZCP_R 167
- 168
- 4.6.43. OUT 169
- 4.6.44. R_Trig 169
- 4.6.46. ZRSTM 172
- 4.6.47. ZRSTD 173
- 4.6.48. SQRT_R 174
- 4.6.49. MOD 174
- 4.6.50. MOD_DI 175
- 4.6.51. MOD_R 175
- 4.6.52. Real_To_Int 176
- 4.6.53. Real_To_DInt 176
- 4.6.54. Int_To_Real 177
- 4.6.55. DInt_To_Real 177
- Example 1: 178
- Example 2: 179
- Example 3: 179
- 4.6.58. Offset _R 182
- 4.7. Application Instruction 183
- 4.7.2. Rotary Cut Parameters 184
- Short material cutting 185
- Equal length cutting 185
- The entry curve 187
- The end curve 188
- 4.7.5.1 189
- 4.7.5.2. APF_RotaryCut_In 191
- 4.7.5.3. APF_RotaryCut_Out 192
- Explanation of areas 197
- Steps for flying shear 197
- Function feature 197
- Shear axis 198
- Sync area 203
- 4.8.1. G Code Input Format 206
- Center of a circle 222
- Start point 222
- Terminal point 222
- （）200,200 223
- Start point Start point 226
- Instruction example 1: 232
- Instruction example 2: 232
- Instruction example: 232
- 4.8.4. DMC_NC 233
- Program example 1: 235
- Program example 2: 236
- ¾ Program: 237
- ¾ Steps: 237
- 5.Troubleshooting 258
- 5. Troubleshooting 259
- Appendix A 264
- Appendix B 287
- Appendix C 301
- Appendix D 333
- Appendix E 338
Related products and manuals for Air compressors Delta D25886
(72 pages)
Air compressors Delta (66-501-1) User Manual
(24 pages)
(24 pages)
© 2020, manymanuals.com. All rights reserved. | 0.859 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals