Delta 50-875 User Manual download pdf (Page 8)

Fig. 8A

USING THE REMOTE CONTROL

To reduce the risk of fire or electric

shock, do not use this unit with any

solid-state speed control device.

The remote control provided with this unit is not con-

sidered a solid-state device.

The Air Cleaner is equipped with a REMOTE CONTROL

(A) Fig.8A.

NOTE: The remote requires two (2) AAA batteries (not

supplied). The Battery housing is located underneath the

back cover.

Notice that the remote control has three control buttons

(Fig. 8A): TIME (B), ON/OFF (C), and SPEED (D). These

buttons correspond to the LED sensor panel on the rear

of the machine (K) Fig. 10B.

NOTE: When the machine is connected to the power

source, a green light (E) will be activated on the panel.

To activate the blower unit, press the “ON/OFF” button

of Low or “L” on the sensor panel. Press the SPEED

button once, and the machine will run at the high (or “H”

level). Press the SPEED button again, and the machine

will run at the medium speed (or “M”). Press the SPEED

button a third time, and the machine will return to the

Low Speed mode.

To turn the machine off, press the “ON/OFF” button (C)

Fig. 8A.

Fig. 8B

This unit has a timer that can be set by remote control.

When the “TIME” button (B) Fig. 8A is pressed on the

remote control, the machine will run for 1/2 hour. (An

LED light will show up on the sensor panel (F) Fig. 8B).

Pressing the “TIME” button again will set the machine to

run for one hour. Notice that the light on the sensor

panel has now moved to the 1H location (G) Fig. 8B.

When the “TIME” button is pressed a third time, the

machine will run for two hours. At this point, the green

light will show up under the two hour location (H). When

you press the “TIME” button the fourth time, the unit will

run for four hours. Notice that the indicator light (J)

glows at the four hour mark.

All of these functions can be manually controlled by

using the two buttons on the sensor panel (K) Fig. 8B.

The Delta 50-875 Air Cleaner can be used in

a. bench-top sanding applications.

b. circular saw applications.

c. dry wall applications.

d. shop cleaning applications.

e. floor sanding applications.

f. any other application where non-metallic dust is a factor.

NOTE: The air cleaner may produce a slight odor for the first few hours of operation due to the protective coating which

is applied to internal components. This odor will dissipate and should be disregarded.

IMPORTANT: Never operate the air cleaner without air filters in place.

OPERATION

CHANGING AND CLEANING FILTERS

The model 50-875 Air Cleaner has an “air flow” indicator (A) Fig. 9A located on the left side of the unit. To check the

filters, turn the unit “ON”. If the indicator points to “green” (B) Fig. 9A, the filters are clean. Clean (or change) the filters

when the indicator points to “red” (C) Fig. 9A as follows:

1. Turn the unit “OFF”.

2. Remove the outer first stage filter (A) Fig. 9B by lifting and pulling out on the bottom of the filter. Clean or replace

the first stage filter depending on its condition. Clean this filter in one of two ways: Use a shop vac to remove the

dust, or use compressed air (30 psi maximum) to blow the dust out of the filter. If you replace the outer filter, check

to see if the filter has an air flow arrow (A) Fig 9D. If so, point the arrow inward. If the filter does not have an air

flow arrow, install the filter either way.

MAINTENANCE

1 2 3 4 5 6 7 8 9 10 11

Comments to this Manuals

No comments

Delta 50-875 User Manual Page 8

Comments to this Manuals