Delta 34-814 Instruction Manual

Browse online or download Instruction Manual for Circular saws Delta 34-814. Delta 34-814 Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 28
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
INSTRUCTION MANUAL
UNISAW
®
10" Right Tilting Arbor Saw
(Models 34-801, 34-806, 34-814, 36-812)
PART NO. 422-04-651-0064 (01-15-02)
Copyright © 2002 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Page view 0
1 2 3 4 5 6 ... 27 28

Summary of Contents

Page 1 - INSTRUCTION MANUAL

INSTRUCTION MANUALUNISAW®10" Right Tilting Arbor Saw(Models 34-801, 34-806, 34-814, 36-812) PART NO. 422-04-651-0064 (01-15-02)Copyright © 2002 D

Page 2 - GENERAL SAFETY RULES

10Fig. 16 Fig. 17Fig. 19ADBFAJFig. 18Fig. 20 Fig. 214. If an adjustment is necessary, loosen two screws (F)Fig. 17, and adjust splitter bracket (A) un

Page 3 - Refer to them often

11Fig. 22Fig. 23Fig. 25Fig. 24Fig. 26 Fig. 27APBXZY8. Assemble upper splitter bracket (M) Fig. 22, to lowerbracket (L) using a 5/16-18x1" hex hea

Page 4 - GROUNDING INSTRUCTIONS

12Fig. 28Fig. 30EFig. 29FASTENING MOTOR CORD TO SAW FRAME1. IMPORTANT: Turn the blade tilting handwheelcounterclockwise as far as it will go until the

Page 5 - MAGNETIC PUSH BUTTON CONTROLS

13Fig. 35Fig. 36ASSEMBLING RIP FENCE HOLDER BRACKETSAssemble the rip fence holder brackets (A) and (B) Fig.37, to the four holes located in the left h

Page 6 - OPERATING INSTRUCTIONS

14OPERATING CONTROLS AND UNISAW ADJUSTMENTSSTARTING AND STOPPING THE SAWTo start the machine, push “ON” button (A) Fig. 39. Tostop the machine, push “

Page 7 - ASSEMBLY INSTRUCTIONS

15ADJUSTING 90 AND 45DEGREE POSITIVE STOPSPositive stops are provided to quickly and accuratelyposition the blade at 90 and 45 degrees to the table. T

Page 8 - ASSEMBLING LVC ON/OFF

16ADJUSTING TABLE INSERTPlace a straight edge (B) across the table at both ends ofthe table insert as shown in Fig. 46. The table insert (A)should alw

Page 9 - ASSEMBLY

17MAINTENANCECHANGING THE SAW BLADE1. DISCONNECT MACHINE FROM POWER SOURCE.2. NOTE: Two wrenches are supplied with the saw forchanging the saw blade;

Page 10

18PROTECTING CAST IRON TABLE FROM RUSTTo clean and protect cast iron tables from rust, you will need the following materials: 1 pushblock from a joint

Page 11

19Fig. 56AFig. 57BFig. 58USING THE FENCE AS ACUT-OFF GAGEWARNING: WHEN USING YOUR UNIFENCE AS ACUT-OFF GAGE, MAKE SURE IT IS PROPERLY SETUP AS DESCRIB

Page 12 - TO SAW FRAME

2GENERAL SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain ha

Page 13

20Fig. 61USING AUXILIARY WOOD FACING ON BIESEMEYERRIP FENCEIt is necessary when performing special operations suchas moulding to add wood facing (A) F

Page 14 - AND UNISAW ADJUSTMENTS

21Fig. 65Fig. 66GHWIMPORTANT: For certain cutting operations such asdadoing and moulding where you are not cuttingcompletely through the workpiece, th

Page 15 - ADJUSTING TABLE

22Fig. 69Fig. 70Fig. 71ABCUSING ACCESSORY DADO HEADIMPORTANT: THE BLADE GUARD AND SPLITTERASSEMBLY CANNOT BE USED WHEN DADOING ORMOULDING AND MUST BE

Page 16 - ADJUSTING TABLE INSERT

23CONSTRUCTING A FEATHERBOARDFig. 74, illustrates dimensions for making a typical featherboard. The material which the featherboard is constructedof,

Page 17 - MAINTENANCE

24PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH 1

Page 18 - OPERATIONS

25BLADE GUARD ACCESSORIESDeluxe Uniguard®Blade GuardThe Delta Model 34-976 Uniguard Blade Guard withSplitter and Anti-kickback Fingers Fig. 77, is ana

Page 19 - CUT-OFF GAGE

26Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which

Page 20

27NOTES

Page 21 - AFTER OPERATION IS COMPETE

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER®,INNOVATION THAT WORKS®, JETST

Page 22 - DADO HEAD

3ADDITIONAL SAFETY RULES FORCIRCULAR SAWSWARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURYSAVE THESE INSTRUCTIONS. Refer to

Page 23 - CONSTRUCTING A FEATHERBOARD

4POWER CONNECTIONSA separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected

Page 24 - PUSH STICK

5Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord whichhas a 3-prong grounding type plug

Page 25 - BLADE GUARD ACCESSORIES

6OPERATING INSTRUCTIONSFOREWORDThe Delta Unisaw is a 10" right tilting arbor saw. The Delta Unisaw features set the standards in the table saw in

Page 26 - Two Year Limited Warranty

7ASSEMBLY INSTRUCTIONSWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE SAW TO THE POWER SOURCE UNTIL THESAW IS COMPLETELY ASSEMBLED AND YOU UNDERSTAND

Page 27

8ASSEMBLING LVC STARTERBOX TO CABINETIf you purchased the machine with magnetic pushbutton electrical controls, the saw is shipped with thestarter box

Page 28 - • DELTA)

9ASSEMBLING GPE ON/OFFSWITCH1. The GPE on/off switch (A) Fig. 11, is shippedattached to a mounting bracket at the right side of themachine.2. Loosely

Comments to this Manuals

No comments