Delta 36-5000 Instruction Manual download pdf (Page 4)

100

GENERAL POWER TOOL SAFETY RULES

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

If tool is loaned to someone, also loan them these instructions.

PROPOSITION 65 WARNING:

Dust created by

power sanding, sawing, grinding, drilling, and other

construction activities may contain chemicals known to

the state of California to cause cancer, birth defects or

other reproductive harm. Some examples are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement and other

masonry products

• Asbestos dust

• Arsenic and chromium from chemically-treated

lumber

Your risk from these exposures varies depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well-ventilated

area and work with approved safety equipment, such

as dust masks that are specially designed to filter out

microscopic particles.

18. USE RECOMMENDED ACCESSORIES. Consult

manual for recommended accessories. Use of

inappropriate accessories may cause personal

injury or property damage.

19. NEVER STAND ON TOOL. Serious injury could

occur if the tool tips or if you unintentionally contact

the cutting surface.

20. CHECK TOOLS FOR DAMAGE. Before using,

and after tool or accessory has been dropped or

damaged, check guards and affected parts for

alignment of moving parts, binding of moving

parts, breakage of parts, and any other condition

that may affect its operation to make sure tool will

operate properly and all parts will perform their

intended function. Do not use a damaged product.

A guard or any other part that is damaged should

be properly repaired or replaced using factory-

approved service parts.

21. USE PROPER FEED DIRECTION. Feed workpiece

against the direction of rotation of the tool’s blade,

cutter, or abrasive surface. Feeding in the other

direction may cause the workpiece to be thrown at

high speed.

22. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Do not leave tool until it comes

to a complete stop. In the event of a power failure,

move switch to “OFF” position.

23. STAY ALERT, WATCH WHAT YOU ARE DOING,

AND USE COMMON SENSE. Do not use power

tools when tired or under the influence of drugs,

alcohol, or medication. A moment of inattention

while operating power tools may result in injury.

24. SERVICE PARTS. Use only identical replacement

parts when servicing your tool.

25. WEAR PROPER APPAREL. Do not wear loose

clothing, gloves, neckties, rings, bracelets, or other

jewelry which may get caught in moving parts.

Nonslip protective footwear is recommended. Wear

protective hair covering to contain long hair.

26. WEAR PROPER EYE PROTECTION. All persons

in work area should wear safety glasses with side

shields. Everyday eyeglasses with impact resistant

lenses are not safety glasses. Eye equipment

should comply with ANSI Z87.1 standards.

27. HEARING PROTECTION. All people in work area

should wear proper hearing protection consistent

with noise levels and exposure. Hearing equipment

should comply with ANSI S3.19 standards.

28. DUST PROTECTION. Use of power tools can

generate and/or disburse dust, which may cause

serious and permanent respiratory or other injury,

including silicosis (a serious lung disease), cancer,

and death. Direct particles away from face and

body. Always operate tool in well-ventilated area

and provide for proper dust removal. Use dust

collection system whenever possible. Avoid

breathing dust and avoid prolonged contact with

dust. Allowing dust to get into your mouth or eyes,

or lay on your skin may promote absorption of

harmful material. Use properly fitting NIOSH/OSHA

approved respiratory protection appropriate for the

dust exposure and wash exposed areas with soap

and water.

1 2 3 4 5 6 7 8 9 ... 99 100

Comments to this Manuals

No comments

Delta 36-5000 Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for Circular saws Delta 36-5000