Delta 36-714B User Manual

Browse online or download User Manual for Circular saws Delta 36-714B. Unifence™ Saw Guide 52" Capacity

  • Download
  • Add to my manuals
  • Print
  • Page
    / 20
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
INSTRUCTION MANUAL
Unifence™ Saw Guide
52" Capacity
(Model 36-889)
PART NO. 422-27-655-0071 (017)
Copyright © 2001 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Page view 0
1 2 3 4 5 6 ... 19 20

Summary of Contents

Page 1 - 52" Capacity

INSTRUCTION MANUALUnifence™ Saw Guide52" Capacity (Model 36-889)PART NO. 422-27-655-0071 (017)Copyright © 2001 Delta MachineryTo learn more abou

Page 2 - UNPACKING

10ASSEMBLING UNIFENCEBODY TO GUIDE RAIL1. Turn fence body (A) Fig. 32, upside down and lay iton a table or bench. Pull handle (B) out against fencebod

Page 3

11ASSEMBLING FENCE TOUNIFENCE BODY1. The fence (A) can be assembled to clamp plate (B) ineither the horizontal position as shown in Fig. 36, or thever

Page 4 - SHELF TO SAW CABINET

123. When ripping thin stock, it is sometimes moreconvenient to use the fence in the horizontal position, asshown in Fig. 40.4. To move the fence alon

Page 5 - FOR ALL TABLE SAWS

13Fig. 44Fig. 45Fig. 46Fig. 47RIPPING WITH THEUNIFENCERipping is the operation of making a lengthwise cutthrough a board, as shown in Fig. 44, and the

Page 6

14Fig. 48Fig. 49Fig. 50Fig. 51ADJUSTING FENCE PARALLELTO MITER GAUGE SLOTSThe fence (A) Fig. 48, should be adjusted so it is parallelto miter gage slo

Page 7 - GUIDE RAIL TO TABLE

15Fig. 52Fig. 53Fig. 54Fig. 56RIPPING ON LEFT SIDE OFSAW BLADEIn some cases it may be desirable to use the fence on theleft side of the saw blade. Thi

Page 8 - ASSEMBLING RAIL STOP

16USING AUXILIARY WOODFACING ON THE UNIFENCEFig. 57It is necessary when performing special operations suchas when using the moulding cutterhead to add

Page 9 - ASSEMBLING CURSOR TO

17PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH 1

Page 11 - FENCE OPERATION

19Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which

Page 12

2INTRODUCTIONThe model 36-889, 52” capacity Unifence™Saw Guide can be assembled to the Delta 10” Tilting Arbor Saw, 10”Unisaw, Contractors Saw, in add

Page 13 - UNIFENCE

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER®,INNOVATION THAT WORKS®, JETST

Page 14

3Fig. 2Fig. 3Fig. 440"15"

Page 15 - CUT-OFF GAUGE

4ASSEMBLING TABLE ANDSHELF TO SAW CABINET1. Remove the right table extension wing and front andrear guide rails from the saw.2. Lay the table upside d

Page 16 - FACING ON THE UNIFENCE

56. Fasten the front (F) and rear table (G) supports Fig.10, to the bottom of the table as shown using four#8x7/8" long wood screws (H) supplied.

Page 17 - PUSH STICK

6Fig. 15Fig. 16MOUNTING 52" UNIFENCESHELF TO UNISAW WITHMETAL MOTOR COVER11. Fasten lower shelf bracket (V) Fig. 17, to one end oflower shelf (W)

Page 18

7ASSEMBLING UNIFENCEGUIDE RAIL TO TABLE1. Locate the Guide Rail and mounting hardware fromthe packing material of the Unifence.2. The guide rail has e

Page 19 - ACCESSORIES

86. Slide the guide rail along until the “0” on the Unifencescale is aligned with the right edge of the saw table. Snugthe hex nuts on the saw and ext

Page 20 - • DELTA)

9ADJUSTING FLIP STOP1. The Flip Stop Assembly Fig. 28, can be adjusted toany number of positions along the guide rail providing aquick stop setting fo

Comments to this Manuals

No comments