Delta 36-902 Instruction Manual

Browse online or download Instruction Manual for Circular saws Delta 36-902. Delta 36-902 Instruction manual [en] User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 20
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
INSTRUCTION MANUAL
Unifence™ Saw Guide
30" Capacity
(Model 36-902)
PART NO. 422-27-655-0068 - 02-14-03
Copyright © 2003 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Page view 0
1 2 3 4 5 6 ... 19 20

Summary of Contents

Page 1 - 30" Capacity

INSTRUCTION MANUALUnifence™ Saw Guide30" Capacity (Model 36-902)PART NO. 422-27-655-0068 - 02-14-03Copyright © 2003 Delta MachineryTo learn more

Page 2 - UNPACKING

10ADJUSTING RAIL STOP1. The Rail Stop Assembly Fig. 30, can be adjusted toany number of positions along the guide rail providing aquick stop setting f

Page 3

11ASSEMBLING UNIFENCEBODY TO GUIDE RAIL1. Turn fence body (A) Fig. 34, upside down and lay iton a table or bench. Push handle (B) in against fencebody

Page 4 - ASSEMBLING TABLE

12ASSEMBLING FENCE TOUNIFENCE BODY1. The fence (A) can be assembled to clamp plate (B) ineither the horizontal position as shown in Fig. 38, or thever

Page 5

133. When ripping thin stock, it is sometimes moreconvenient to use the fence in the horizontal position, asshown in Fig. 42.4. To move the fence alon

Page 6 - FOR ALL TABLE SAWS

14Fig. 46Fig. 47Fig. 48Fig. 49RIPPING WITH THEUNIFENCERipping is the operation of making a lengthwise cutthrough a board, as shown in Fig. 46, and the

Page 7 - METAL EXTENSION WING

15Fig. 50Fig. 51Fig. 52Fig. 53ADJUSTING FENCE PARALLELTO MITER GAGE SLOTSThe fence (A) Fig. 50, should be adjusted so it is parallelto miter gage slot

Page 8 - GUIDE RAIL TO TABLE

16Fig. 54Fig. 55Fig. 56Fig. 58RIPPING ON LEFT SIDE OFSAW BLADEIn some cases it may be desirable to use the fence on theleft side of the saw blade. Thi

Page 9 - ASSEMBLING RAIL STOP

17USING AUXILIARY WOODFACING ON THE UNIFENCEFig. 59It is necessary when performing special operations suchas when using the moulding cutterhead to add

Page 10 - UNIFENCE BODY

18PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH 1

Page 11 - BODY TO GUIDE RAIL

19Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which

Page 12 - FENCE OPERATION

2INTRODUCTIONThe model 36-902, 30" capacity Unifence™Saw Guide can be assembled to the, Contractors Saw and Unisaw, inaddition to other makes of

Page 13

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

Page 14 - UNIFENCE

3Fig. 2Fig. 3

Page 15

4ASSEMBLING TABLE TO SAW 1. If your saw has a right extension wing, front and rearguide rails, they must be removed.2. Lay the table upside down on th

Page 16 - CUT-OFF GAUGE

55. Fasten the front table support (F) Fig. 9, to thebottom of the table as shown using two #8x7/8" longwood screws (H) and (I) supplied. NOTE: T

Page 17 - FACING ON THE UNIFENCE

6FOR DELTA TABLE SAWS ONLY9. Fasten the table adapter plate (B) to the right side ofthe saw table. Place a 7/16" lockwasher onto a 7/16-20x1"

Page 18 - PUSH STICK

7Fig. 17S13. Using a straight edge (S) Fig. 17, make certain theUnifence table surface is level with the saw table byadjusting two leveling screws loc

Page 19 - ACCESSORIES

8ASSEMBLING UNIFENCEGUIDE RAIL TO TABLE1. Locate the Guide Rail and mounting hardware fromthe packing material of the Unifence.2. The guide rail has e

Page 20 - • DELTA)

96. Slide the guide rail along until the “0” on the Unifencescale is aligned with the right edge of the saw table. Snugthe hex nuts on the saw and ext

Comments to this Manuals

No comments