Delta BS100 Instruction Manual

Browse online or download Instruction Manual for Circular saws Delta BS100. Delta BS100 Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 25
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
INSTRUCTION MANUAL
9" Bench Band Saw
(Model BS100)
PART NO. A03049 - 03-05-04
Copyright © 2004 Delta Machinery
ESPAÑOL: PÁGINA 25
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
26894
RTD10000120AA
Page view 0
1 2 3 4 5 6 ... 24 25

Summary of Contents

Page 1 - 9" Bench Band Saw

INSTRUCTION MANUAL9" Bench Band Saw(Model BS100)PART NO. A03049 - 03-05-04Copyright © 2004 Delta MachineryESPAÑOL: PÁGINA 25To learn more about D

Page 2 - GENERAL SAFETY RULES

101. Fasten the lamp bracket (A) Fig. 13, to the top coverof the machine, using two M6x1x12mm cap headscrews (B) and 1/4" lockwashers as shown.2.

Page 3

11OPERATING CONTROLS AND ADJUSTMENTSFig. 15Fig. 16Fig. 17STARTING ANDSTOPPING SAWThe switch (A) Fig. 15, is located on the front side of theband saw.

Page 4 - SAVE THESE INSTRUCTIONS

12Fig. 19ADJUSTINGBLADE TENSIONBlades of 1/8", 1/4", and 3/8" in width by 59-1/2" inlength are available for use with your band sa

Page 5 - GROUNDING INSTRUCTIONS

13ADJUSTING UPPER BLADEGUIDES AND BLADESUPPORT BEARINGIMPORTANT: BOTH THE UPPER AND LOWERBLADE GUIDES MUST BE PROPERLY ADJUSTEDTO PREVENT THE BLADE FR

Page 6 - OPERATING INSTRUCTIONS

14ADJUSTING LOWER BLADEGUIDES AND BLADESUPPORT BEARINGThe lower blade guides and blade support bearingshould be adjusted at the same time as the upper

Page 7 - 9" BENCH BAND SAW PARTS

15ADJUSTING THE TABLEPOSITIVE STOPSPositive stops are provided for the table at the 90 and 45degree angle to the blade. To check and adjust thepositiv

Page 8 - ASSEMBLY

16Fig. 37AWRENCH STORAGEThe 3mm and 4mm wrenches (A) supplied with yourband saw can be stored inside the wheel cover asshown in Fig. 37A.ACHANGING BLA

Page 9

17Before starting the machine, see that all adjustments are properly made and the guards are in place. Turn the upperwheel by hand to make sure that e

Page 10 - TO SUPPORTING SURFACE

18Fig. 40Fig. 40 illustrates a typical bevel cutting operation using the accessory miter gage.Fig. 41Fig. 41 illustrates a typical resawing applicatio

Page 11

19In spite of how well a band saw is maintained, problems can occur. The following troubleshootingguide will help you solve the more common problems:T

Page 12 - BLADE GUIDE ASSEMBLY

2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

Page 13 - SUPPORT BEARING

20Trouble: BLADE WILL NOT TRACK.Probable CauseRemedy1. Blade too loose 1. Adjust tension2. Upper wheel not properly adjusted. 2. Adjust upper wheel.3.

Page 14 - TILTING THE TABLE

21BAND SAW BLADESA band saw blade is a delicate piece of steel that is subjected to tremendous strain. You canobtain long use from a band saw blade if

Page 17 - OPERATING THE BAND SAW

24PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

Page 18

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

Page 19 - TROUBLESHOOTING GUIDE

3GENERAL SAFETY RULES1. FOR YOUR OWN SAFETY, READ THE INSTRUC-TION MANUAL BEFORE OPERATING THEMACHINE. Learning the machine’s application,limitations,

Page 20

4ADDITIONAL SAFETY RULES FORBAND SAWS1. DO NOT OPERATE THIS MACHINE UNTIL it isassembled and installed according to theinstructions.2. OBTAIN ADVICE f

Page 21 - BAND SAW BLADES

5A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

Page 22

6EXTENSION CORDSUse proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong groun

Page 23

79" BENCH BAND SAW PARTS1 - Band Saw2 - Lamp3 - Lamp Cord Clamps(2)4 - 1/4" Lockwashers (2)5 - M6x1x12mm Cap Head Screws (2)Fig. 26 - Table7

Page 24 - ACCESSORIES

8ASSEMBLYFig. 4ASSEMBLING TABLETO MACHINE1. Locate table locking lever (shown disassembled)Fig. 4, M10 flat washer (B) and 4mm wrench (C).2. Using the

Page 25 - • DELTA)

9Fig. 9Fig. 10Fig. 116. Locate pinion knob (N) Fig. 9, spring (O), and specialscrew (P).7. Position pinion knob (N) Fig. 10, onto the back ofsaw so th

Comments to this Manuals

No comments