Operator's ManualMS-250 Mixed SignalOscilloscope Option
Operator's ManualStandard HardwareThe MS-250 is delivered with the following hardware:Part Description QTYMixed SignalAccessoryProvides 18-channe
MS-250 Mixed Signal Oscilloscope OptionPart Description QTY3" FlexibleGround LeadLead for grounding individual digital inputs 5GroundExtenderConn
Operator's ManualAccessoriesYou may purchase these optional accessories separately to enhance the performance ofan MS-250:Accessory Part Number D
MS-250 Mixed Signal Oscilloscope OptionAccessory Part Number DescriptionSmall GripperProbe SetPK400-3Small gripper probe set for 0.008 inch (0.2 mm) p
Operator's ManualConnecting the Mixed Signal OptionConnecting to the OscilloscopeTo connect the Mixed Signal accessory to your oscilloscope:1. Co
MS-250 Mixed Signal Oscilloscope Option3. Connect the other end of the Bus Cable to the MS-250. Again, be sure to align thewedge and the groove. Faste
Operator's Manual5. Connect the Digital Leadset to the Digital Inputs D0 – D17 connector on the oppositeend of the MS-250 and fasten the thumb sc
MS-250 Mixed Signal Oscilloscope OptionDigital ConnectionsConnect the Digital Leads to the digital lines you wish to observe (using accessory micro-gr
Operator's ManualDigital SetupDigital Logic SetupEach lead bank requires a Logic Setup to determine the assignment of a 1 or 0, dependingon the m
MS-250 Mixed Signal Oscilloscope OptionMinimum Voltage Swing (Hysteresis)You can define the minimum high voltage and maximum low voltage levels using
MS-250 Mixed SignalOscilloscope OptionOperator's ManualNovember 2014
Operator's ManualDigital Group SetupThis procedure organizes the digital lines into groups, which correspond to buses. Thelines within a single g
MS-250 Mixed Signal Oscilloscope OptionDisplaying Digital TracesThe Trace On checkbox is selected by default, so if you are connected to a live input,
Operator's ManualDigital bus trace 1 division high starting at position 4.Store DisplayTo store the entire group and display setup to an internal
MS-250 Mixed Signal Oscilloscope OptionDigital TriggeringSetting UpDigital TriggersTo access the Trigger setup dialogs, do one of the following:l Cho
Operator's Manual1. Open the Digital Pattern dialog.2. At the far right of the dialog, choose either Logic Bus or Logic.3. Optionally, deselect F
MS-250 Mixed Signal Oscilloscope OptionAnalog Pattern1. To add the analog pattern to the digital pattern, leave your digital pattern as is andskip to
Operator's ManualEdge TriggerEdge triggers upon a achieving a certain voltage level in the positive or negative slope ofthe waveform. It is the d
MS-250 Mixed Signal Oscilloscope OptionWidth TriggerWidth triggers upon finding a positive- or negative-going pulse width when measured at thespecifie
Operator's ManualGlitch TriggerGlitch triggers upon finding a fixed pulse-width time or time range.On the Trigger dialog, select Smart trigger ty
MS-250 Mixed Signal Oscilloscope OptionInterval TriggerInterval triggers upon finding a specific interval, the time (period) between twoconsecutive ed
MS-250 Mixed Signal Oscilloscope Option Operator's Manual© 2014 Teledyne LeCroy, Inc. All rights reserved.Unauthorized duplication of Teledyne Le
Operator's ManualDropout TriggerDropout triggers when a signal loss is detected. The trigger is generated at the end of thetimeout period followi
MS-250 Mixed Signal Oscilloscope OptionQualified TriggerQualified arms the trigger on the A event, then fires on the B event. In Normal trigger mode,i
Operator's ManualMaintenanceCleaningClean only the exterior of the product using a soft cloth moistened with water or analcohol solution. Do not
MS-250 Mixed Signal Oscilloscope OptionThe Datasheet published on the product page contains the detailed product specifications.You can also download
Operator's ManualReferenceCertificationsEMC ComplianceEC DECLARATION OF CONFORMITY - EMCThe product meets the intent of EC Directive 2004/108/EC
MS-250 Mixed Signal Oscilloscope OptionSafety ComplianceEC DECLARATION OF CONFORMITY - LOW-VOLTAGEThe product meets the intent of EC Directive 2006/95
Operator's ManualWarrantyTHE WARRANTY BELOW REPLACES ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY
MS-250 Mixed Signal Oscilloscope OptionContact UsUnited States and Canada -World Wide Corporate OfficeTeledyne LeCroy Corporation700 Chestnut Ridge Ro
924976-00November, 2014
Operator's ManualContentsWelcome iiSafety 1Operating Environment 2Specifications 2Introduction 3Technical Overview 3Standard Hardware 5Accessorie
MS-250 Mixed Signal Oscilloscope OptionWelcomeThank you for purchasing a Teledyne LeCroy MS-250 Mixed Signal Oscilloscope Option.The MS-250 is a power
Operator's ManualSafetyObserve these instructions to keep the product operating in a correct and safe condition.You are required to follow genera
MS-250 Mixed Signal Oscilloscope OptionOperating EnvironmentTemperature: 5 to 40 °CHumidity:Maximum relative humidity 80% (non-condensing) for tempera
Operator's ManualIntroductionThe MS-250 Mixed Signal Oscilloscope Option is a complete system that adds digitalacquisition and triggering capabil
MS-250 Mixed Signal Oscilloscope OptionThe minimum high voltage level may be defined by the user (using the hysteresis controls)up to 1.4 V above the
Comments to this Manuals