Delta 1.07 VFD-D D User Manual download pdf (Page 127)

Chapter 6 Fault Codes and Descriptions |DD Series

6-6

Display Description Corrective Actions

Door width auto-tuning error

Check the wiring of the encoder

Open door time-out

Check if door opens fluently.

6.1.1 Reset

There are three methods to reset the AC motor drive after the fault is corrected:

1. Press

RESET

STOP

key on KPV-CE01.

2. Set external terminal to “RESET” and then set the contact ON.

3. Send “RESET” command by communication.

NOTE

Make sure that RUN command or signal is OFF before executing RESET to prevent damage or

personal injury due to immediate operation.

1 2 ... 122 123 124 125 126 127 128 129 130 131 132 ... 140 141

''( 1
 1
Preface 2
Table of Content 5
Chapter 1 Introduction 7
1-1 Receiving and Inspection 8
T02DD21A0 9
Minimum Mounting Clearances 10
CAUTION! 11
Dimensions for Motor 12
ECMD-B9160GMS 13
Chapter 2 Wiring 14
2-1 Wiring Diagram 15
Used with external power 16
Not allowed 17
2-2 Main Circuit Terminal 18
Chapter 2 Wiring 19
2-3 Control Circuit Terminal 20
3-1 Operation Method 23
3-2 Keypad Descriptions 24
Chapter 4 Parameter Settings 25
Settings 28
Parameter Reset 48
Start-up Display Selection 48
Software version 49
Password Input 49
Password Set 49
Control Method 50
Door Control Mode 51
Output Direction 52
Demo Mode 53
Frequency Testing Command 53
Motor Auto Tuning (PM) 55
Motor Auto Tuning (IM) 57
Output Voltage 3 61
Output Frequency 4 61
Output Voltage 4 61
OD:("OPEN":STOP) 62
CD:(" OPEN": STOP) 62
Multi-function Output (MO3) 65
Digital Output Direction 66
Position Detection Signal 1 66
Encoder (PG) Signal Type 68
Encoder pulse 68
Encoder Input Type Setting 68
Door Width Pulses (Unit:1) 70
04.19=S1 73
04.20=S2 73
Freqeunc 73
VFPG SVC FOCPG 74
05.19=S1 77
05.20=S2 77
Door Re-open Detection Time 79
Quadrant I 80
Quadrant II 80
Quadrant III 80
Quadrant IV 80
Low Voltage Level 81
Position Control Mode 82
VFPG SVC FOCPG FOCPM 84
Auto Restart After Fault 85
Gain for Speed Feed Forward 88
VFPG SVC FOCPG FOCPM 89
Communication Address 90
Transmission Speed 90
Transmission Fault Treatment 90
Time-out Detection 90
Communication Protocol 90
Code Description: 91
Status monitor 97
Read only 97
Example: 98
Response Delay Time 99
Multi-function Output RY1 103
Multi-function Output RY2 103
View User-defined Parameters 103
2 1 1B 104
111x16 + x16 =16+11 = 104
Enter 2127 104
Chapter 5 Troubleshooting 106
5-1 Over Current (oc) 107
5-2 Ground Fault (GFF) 108
5-3 Over Voltage (ov) 109
5-4 Low Voltage (Lv) 110
5-5 Over Heat (oH1) 111
5-6 Overload (oL) 112
5-8 Phase Loss (PHL) 114
5-9 Motor is not Running 115
5-12 Motor Run Error 118
5.14 Environmental Condition 120
High Harmonic at Power Side 121
Motor Temperature Rises 121
6.1.1 Reset 127
 Voltage 128
 Keypad 128
 Mechanical parts 128
 Main circuit 129
 Resistor of main circuit 130
Control Characteristics 132
Motor Model 134
Appendix B 135
B-1 Capacity Formulas 136
Symbol explanation 137
B-2 General Precautions 138
Drives Selection 138
Parameter Settings 138
Standard motor 139
Special motors: 140
Power Transmission Mechanism 140
Motor torque 141

Comments to this Manuals

No comments

Delta 1.07 VFD-D D User Manual Page 127

Comments to this Manuals