Delta 1.07 VFD-D D User Manual Page 52
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 Parameter Settings|DD Series
4-28
08.00
Zero Step
Speed
08. 01
08. 02
08. 03
08. 04
08. 05
08. 06
08. 07
08.15
15th Step
Speed
08. 14
14t h Step
Speed
08.13
13th Step
Speed
08.12
12th Step
Speed
08. 11
11t h Step
Speed
08. 10
10t h Step
Speed
08. 09
9th Step
Speed
08.08
8th Step
Speed
Close Door Limit
Open Door Limit
Close Door
(FWD)
Open Doo
r
(REV)
1st Step
Speed
2nd Step
Speed
3rd St ep
Speed
4th Step
Speed
5th Step
Speed
6th Step
Speed
7th Step
Speed
3: Speed Control mode
For operating the door, it switches speed by external signal and uses limit switch to deal with completed
position. The signals must be edge trigger. In this mode, it needs to run the door to the close complete
position after power on again or AC motor drive stops.
Door Close
Holding Speed
Open Door (REV
)
Door Open Limit
0.0%
100.0%
Close Door (FWD)
04.00
Door Open
Speed
by I ni tial
04.08
Door Open
Acceleration
Time 1
04.09
Door Open
Deceleration
Time 1
04.03
Door Open High Speed 1
04.05
Door Open
Final Speed
04.02
Door Open Time by
Initial Speed
Door Open
Speed Switch
Signal
Door Open
Limit Signal
04.07
Door Open
Holding Speed
05.03
Door Close
High Spee d 1
05.08
D oor Clo s e
Acceleration Time 1
05.05
Door Close
Limit Signal
05.07
05.09
05.01
Door Close
Distance by
Initial Speed
05.00
Door Close
Initial Speed
Door Close Limit
Door Close
Final Speed
Door C lose
Final Speed
Door Close
Speed Switch
Signal
Output Direction
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 0
Settings
0: Runs in same direction as setting
1: Runs in different direction than setting
PWM Carrier Frequency Selection
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 10
Settings 2~15kHz
- ''( 1
- 1
- Preface 2
- Table of Content 5
- Chapter 1 Introduction 7
- 1-1 Receiving and Inspection 8
- T02DD21A0 9
- Minimum Mounting Clearances 10
- CAUTION! 11
- Dimensions for Motor 12
- ECMD-B9160GMS 13
- Chapter 2 Wiring 14
- 2-1 Wiring Diagram 15
- Used with external power 16
- Not allowed 17
- 2-2 Main Circuit Terminal 18
- Chapter 2 Wiring 19
- 2-3 Control Circuit Terminal 20
- 3-1 Operation Method 23
- 3-2 Keypad Descriptions 24
- Chapter 4 Parameter Settings 25
- Settings 28
- Parameter Reset 48
- Start-up Display Selection 48
- Software version 49
- Password Input 49
- Password Set 49
- Control Method 50
- Door Control Mode 51
- Output Direction 52
- Demo Mode 53
- Frequency Testing Command 53
- Motor Auto Tuning (PM) 55
- Motor Auto Tuning (IM) 57
- Output Voltage 3 61
- Output Frequency 4 61
- Output Voltage 4 61
- OD:("OPEN":STOP) 62
- CD:(" OPEN": STOP) 62
- Multi-function Output (MO3) 65
- Digital Output Direction 66
- Position Detection Signal 1 66
- Encoder (PG) Signal Type 68
- Encoder pulse 68
- Encoder Input Type Setting 68
- Door Width Pulses (Unit:1) 70
- 04.19=S1 73
- 04.20=S2 73
- Freqeunc 73
- VFPG SVC FOCPG 74
- 05.19=S1 77
- 05.20=S2 77
- Door Re-open Detection Time 79
- Quadrant I 80
- Quadrant II 80
- Quadrant III 80
- Quadrant IV 80
- Low Voltage Level 81
- Position Control Mode 82
- VFPG SVC FOCPG FOCPM 84
- Auto Restart After Fault 85
- Gain for Speed Feed Forward 88
- VFPG SVC FOCPG FOCPM 89
- Communication Address 90
- Transmission Speed 90
- Transmission Fault Treatment 90
- Time-out Detection 90
- Communication Protocol 90
- Code Description: 91
- Status monitor 97
- Read only 97
- Example: 98
- Response Delay Time 99
- Multi-function Output RY1 103
- Multi-function Output RY2 103
- View User-defined Parameters 103
- 2 1 1B 104
- 111x16 + x16 =16+11 = 104
- Enter 2127 104
- Chapter 5 Troubleshooting 106
- 5-1 Over Current (oc) 107
- 5-2 Ground Fault (GFF) 108
- 5-3 Over Voltage (ov) 109
- 5-4 Low Voltage (Lv) 110
- 5-5 Over Heat (oH1) 111
- 5-6 Overload (oL) 112
- 5-8 Phase Loss (PHL) 114
- 5-9 Motor is not Running 115
- 5-12 Motor Run Error 118
- 5.14 Environmental Condition 120
- High Harmonic at Power Side 121
- Motor Temperature Rises 121
- 6.1.1 Reset 127
- Voltage 128
- Keypad 128
- Mechanical parts 128
- Main circuit 129
- Resistor of main circuit 130
- Control Characteristics 132
- Motor Model 134
- Appendix B 135
- B-1 Capacity Formulas 136
- Symbol explanation 137
- B-2 General Precautions 138
- Drives Selection 138
- Parameter Settings 138
- Standard motor 139
- Special motors: 140
- Power Transmission Mechanism 140
- Motor torque 141
© 2020, manymanuals.com. All rights reserved. | 0.299 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals