Delta 1.07 VFD-D D User Manual Page 63
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 Parameter Settings|DD Series
4-39
8: 1st, 2nd acceleration/deceleration time selection
○ ○ ○ ○ ○
9: Force stop (NO) input
○ ○ ○ ○ ○
10: Demo mode
○ ○ ○ ○ ○
11: Emergency stop (NO) input
○ ○ ○ ○ ○
12: Source of operation command (Keypad/External terminals)
○ ○ ○ ○ ○
13: Parameter lock enable (NC)
○ ○ ○ ○ ○
14: Door open complete signal
○ ○ ○ ○ ○
15: Door close complete signal
○ ○ ○ ○ ○
16: Door open speed switch signal
○ ○ ○ ○ ○
17: Door close speed switch signal
○ ○ ○ ○ ○
18: Open allowance signal
○ ○ ○ ○ ○
19: Screen signal input
○ ○ ○ ○ ○
20: Door curve signal input for 2nd set door open/close
○ ○ ○ ○ ○
21: Reset signal input
○ ○ ○ ○ ○
22: Input system security circuit confirmation signal (DCC) ○ ○ ○ ○ ○
23: Input enforced door closing signal (NUD) ○ ○ ○ ○ ○
This parameter selects the functions for each multi-function terminal.
Summary of Function Settings:
Settings Functions Descriptions
0
No function
Any unused terminals should be programmed to 0 to insure the
y
have no effect on operation.
1
Multi-step speed command 1
2
Multi-step speed command 2
3
Multi-step speed command 3
4
Multi-step speed command 4
When door control mode (Pr.00-09)is set 2 (multi-step speed
control), these four inputs can be used for 16 step speed
frequencies
5
Fault reset Reset drive setting after fault is cleared.
6
Low speed operation Before using this function, please make sure that AC motor drive is
stop. At this moment, key “STOP” on the digital keypad is still valid.
When this contact is OFF, motor will stop by deceleration time of
low speed operation.
7
OD/CD command for low
speed operation
ON: open the door (OD)
OFF: closer the door (CD)
This command will be effective only when external terminal for low
speed operation is active.
8
1st, 2nd
acceleration/deceleration
time selection
When signal is input, the AC motor drive can switch between 1st
and 2nd acceleration/deceleration time
9
Force stop (NO) input This parameter has the same function as the “STOP” command
and no error message will be displayed. It does not require a
RESET but a new RUN command is needed for the drive to run
again.
10
Demo mode When this setting is enabled, the output frequency of AC motor
drive will run by open/close curve repeatedly till this setting is
disabled. It will get the best open/close curve by this action.
11
Emergency stop (NO) input When setting to 11, the Multi-Function Input Terminal can be used
to stop the AC motor drive in case of malfunction in the application.
It will display “EF”. Please “RESET” after the fault has been
cleared.
12
Source of operation
command (Keypad/External
terminals)
ON: Operation command via Ext. Terminals
OFF: Operation command via Keypad
Pr.00-14 is disabled if this parameter is set to 13.
13
Parameter lock enable (NC) When this setting is enabled, all parameter reading value will be
00. This setting must be disabled in order to read the parameter
content.
- ''( 1
- 1
- Preface 2
- Table of Content 5
- Chapter 1 Introduction 7
- 1-1 Receiving and Inspection 8
- T02DD21A0 9
- Minimum Mounting Clearances 10
- CAUTION! 11
- Dimensions for Motor 12
- ECMD-B9160GMS 13
- Chapter 2 Wiring 14
- 2-1 Wiring Diagram 15
- Used with external power 16
- Not allowed 17
- 2-2 Main Circuit Terminal 18
- Chapter 2 Wiring 19
- 2-3 Control Circuit Terminal 20
- 3-1 Operation Method 23
- 3-2 Keypad Descriptions 24
- Chapter 4 Parameter Settings 25
- Settings 28
- Parameter Reset 48
- Start-up Display Selection 48
- Software version 49
- Password Input 49
- Password Set 49
- Control Method 50
- Door Control Mode 51
- Output Direction 52
- Demo Mode 53
- Frequency Testing Command 53
- Motor Auto Tuning (PM) 55
- Motor Auto Tuning (IM) 57
- Output Voltage 3 61
- Output Frequency 4 61
- Output Voltage 4 61
- OD:("OPEN":STOP) 62
- CD:(" OPEN": STOP) 62
- Multi-function Output (MO3) 65
- Digital Output Direction 66
- Position Detection Signal 1 66
- Encoder (PG) Signal Type 68
- Encoder pulse 68
- Encoder Input Type Setting 68
- Door Width Pulses (Unit:1) 70
- 04.19=S1 73
- 04.20=S2 73
- Freqeunc 73
- VFPG SVC FOCPG 74
- 05.19=S1 77
- 05.20=S2 77
- Door Re-open Detection Time 79
- Quadrant I 80
- Quadrant II 80
- Quadrant III 80
- Quadrant IV 80
- Low Voltage Level 81
- Position Control Mode 82
- VFPG SVC FOCPG FOCPM 84
- Auto Restart After Fault 85
- Gain for Speed Feed Forward 88
- VFPG SVC FOCPG FOCPM 89
- Communication Address 90
- Transmission Speed 90
- Transmission Fault Treatment 90
- Time-out Detection 90
- Communication Protocol 90
- Code Description: 91
- Status monitor 97
- Read only 97
- Example: 98
- Response Delay Time 99
- Multi-function Output RY1 103
- Multi-function Output RY2 103
- View User-defined Parameters 103
- 2 1 1B 104
- 111x16 + x16 =16+11 = 104
- Enter 2127 104
- Chapter 5 Troubleshooting 106
- 5-1 Over Current (oc) 107
- 5-2 Ground Fault (GFF) 108
- 5-3 Over Voltage (ov) 109
- 5-4 Low Voltage (Lv) 110
- 5-5 Over Heat (oH1) 111
- 5-6 Overload (oL) 112
- 5-8 Phase Loss (PHL) 114
- 5-9 Motor is not Running 115
- 5-12 Motor Run Error 118
- 5.14 Environmental Condition 120
- High Harmonic at Power Side 121
- Motor Temperature Rises 121
- 6.1.1 Reset 127
- Voltage 128
- Keypad 128
- Mechanical parts 128
- Main circuit 129
- Resistor of main circuit 130
- Control Characteristics 132
- Motor Model 134
- Appendix B 135
- B-1 Capacity Formulas 136
- Symbol explanation 137
- B-2 General Precautions 138
- Drives Selection 138
- Parameter Settings 138
- Standard motor 139
- Special motors: 140
- Power Transmission Mechanism 140
- Motor torque 141
© 2020, manymanuals.com. All rights reserved. | 3.134 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals