Delta 1.07 VFD-D D User Manual Page 64
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 Parameter Settings|DD Series
4-40
14
Door open complete signal When Pr.06-11 is set to 01 or 03, drive will open the door to the
completed position by this signal.
15
Door close complete signal When Pr.06-11 is set to 02 or 03, drive will close the door to the
completed position by this signal.
16
Door open speed switch
signal
When door control mode (pr.00-09) is set to 3 speed control mode,
this terminal can be used for switching speed.
17
Door close speed switch
signal
When door control mode (pr.00-09) is set to 3 speed control mode,
this terminal can be used for switching speed.
18
Open allowance signal When this setting is enabled, it allows opening the door. It also can
be used for the signal of door zone.
19
Screen signal input
20
Door curve signal input for
2nd step door open/close
When this setting is ON, it will run the curve of 2nd step doo
r
open/close.
21
Reset signal input When parameter is set to 21, the drive re-positioning begins.
22
Input system security circuit
confirmation signal (DCC)
When the motor drive receives this signal then any door closing
signal will not be input. And the door will remain at the actuation
position
23
Input enforced door closing
signal (NUD)
When the motor drive receives this signal, it will close at low speed
(Pr03-10), but does not respond to stop closing door function.
Digital Terminal Input Debouncing Time (MD-5-13)
Control mode
VF
VFPG SVC FOCPG FOCPM
Factory setting: 0.005
Settings 0.001~30.000sec
This parameter is to delay the signals on digital input terminals. 1 unit is 2.5 msec. The delay time is to
debounce noisy signals that could cause the digital terminals to malfunction but response time maybe a
bit slower.
Digital Input Operation Direction
Control mode
VF
VFPG SVC FOCPG FOCPM
Factory setting: 60
Settings
0～65535
This parameter is used to set the input signal level.
bit 0 is CD terminal, bit 1is OD terminal and bit 2~bit 6 areMI1~MI5。
User can change the terminal status ON/OFF by communicating.
For example, MI1 is set to 1 (multi-step speed command 1), MI2 is set to 2 (multi-step speed command
2). Then the forward + 2nd step speed command=1001(binary) =9 (Decimal). Only need to set
Pr.02-07=9 by communication and it can forward with 2nd step speed. It doesn’t need to wire any
multi-function terminal.
bit6 bit5 bit4 bit3 bit2 bit1 bit0
MI5 MI4 MI3 MI2 MI1 OD CD
Multi-function Output (Relay1)
Factory setting: 16
Multi-function Output (Relay2)
Factory setting: 17
Multi-function Output (MO1)
Factory setting: 0
Multi-function Output (MO2)
Factory setting: 0
- ''( 1
- 1
- Preface 2
- Table of Content 5
- Chapter 1 Introduction 7
- 1-1 Receiving and Inspection 8
- T02DD21A0 9
- Minimum Mounting Clearances 10
- CAUTION! 11
- Dimensions for Motor 12
- ECMD-B9160GMS 13
- Chapter 2 Wiring 14
- 2-1 Wiring Diagram 15
- Used with external power 16
- Not allowed 17
- 2-2 Main Circuit Terminal 18
- Chapter 2 Wiring 19
- 2-3 Control Circuit Terminal 20
- 3-1 Operation Method 23
- 3-2 Keypad Descriptions 24
- Chapter 4 Parameter Settings 25
- Settings 28
- Parameter Reset 48
- Start-up Display Selection 48
- Software version 49
- Password Input 49
- Password Set 49
- Control Method 50
- Door Control Mode 51
- Output Direction 52
- Demo Mode 53
- Frequency Testing Command 53
- Motor Auto Tuning (PM) 55
- Motor Auto Tuning (IM) 57
- Output Voltage 3 61
- Output Frequency 4 61
- Output Voltage 4 61
- OD:("OPEN":STOP) 62
- CD:(" OPEN": STOP) 62
- Multi-function Output (MO3) 65
- Digital Output Direction 66
- Position Detection Signal 1 66
- Encoder (PG) Signal Type 68
- Encoder pulse 68
- Encoder Input Type Setting 68
- Door Width Pulses (Unit:1) 70
- 04.19=S1 73
- 04.20=S2 73
- Freqeunc 73
- VFPG SVC FOCPG 74
- 05.19=S1 77
- 05.20=S2 77
- Door Re-open Detection Time 79
- Quadrant I 80
- Quadrant II 80
- Quadrant III 80
- Quadrant IV 80
- Low Voltage Level 81
- Position Control Mode 82
- VFPG SVC FOCPG FOCPM 84
- Auto Restart After Fault 85
- Gain for Speed Feed Forward 88
- VFPG SVC FOCPG FOCPM 89
- Communication Address 90
- Transmission Speed 90
- Transmission Fault Treatment 90
- Time-out Detection 90
- Communication Protocol 90
- Code Description: 91
- Status monitor 97
- Read only 97
- Example: 98
- Response Delay Time 99
- Multi-function Output RY1 103
- Multi-function Output RY2 103
- View User-defined Parameters 103
- 2 1 1B 104
- 111x16 + x16 =16+11 = 104
- Enter 2127 104
- Chapter 5 Troubleshooting 106
- 5-1 Over Current (oc) 107
- 5-2 Ground Fault (GFF) 108
- 5-3 Over Voltage (ov) 109
- 5-4 Low Voltage (Lv) 110
- 5-5 Over Heat (oH1) 111
- 5-6 Overload (oL) 112
- 5-8 Phase Loss (PHL) 114
- 5-9 Motor is not Running 115
- 5-12 Motor Run Error 118
- 5.14 Environmental Condition 120
- High Harmonic at Power Side 121
- Motor Temperature Rises 121
- 6.1.1 Reset 127
- Voltage 128
- Keypad 128
- Mechanical parts 128
- Main circuit 129
- Resistor of main circuit 130
- Control Characteristics 132
- Motor Model 134
- Appendix B 135
- B-1 Capacity Formulas 136
- Symbol explanation 137
- B-2 General Precautions 138
- Drives Selection 138
- Parameter Settings 138
- Standard motor 139
- Special motors: 140
- Power Transmission Mechanism 140
- Motor torque 141
© 2020, manymanuals.com. All rights reserved. | 0.693 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals