Delta 1.07 VFD-D D User Manual Page 65
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 Parameter Settings|DD Series
4-41
Multi-function Output (MO3)
Factory setting: 0
Settings Control mode
VF VFPG SVC FOCPG FOCPM
0: No function
○ ○ ○ ○ ○
1: AC drive in operation
○ ○ ○ ○ ○
2: Zero speed frequency signal (including STOP)
○ ○ ○ ○ ○
3: AC drive ready
○ ○ ○ ○ ○
4: Low voltage warning(Lv)
○ ○ ○ ○ ○
5: Fault indication
○ ○ ○ ○ ○
6: Overhead warning (Pr.06.09)
○ ○ ○ ○ ○
7: Detection of braking resistor action level
○ ○ ○ ○ ○
8: Warning indication
○ ○ ○ ○ ○
9: Over voltage warning
○ ○ ○ ○ ○
10: OD command
○ ○ ○ ○ ○
11: CD command
○ ○ ○ ○ ○
12: Demo Indication
○ ○ ○ ○ ○
13: Demo complete
○ ○ ○ ○ ○
14: Emergency stop indication
○ ○ ○ ○ ○
15: Force stop indication
○ ○ ○ ○ ○
16: Door open complete (limit) signal output
○ ○ ○ ○ ○
17: Door close complete (limit) signal output
○ ○ ○ ○ ○
18: Door Close Error
○ ○ ○ ○ ○
19: Position Complete Signal
○ ○ ○ ○ ○
20: Position Detection 1(for door close only)
○ ○ ○ ○ ○
21: Position Detection 2(for door close only)
○ ○ ○ ○ ○
22: Position Detection 3(for door close only))
○ ○ ○ ○ ○
23: Position Detection 1(for door open only)
○ ○ ○ ○ ○
24: Position Detection 2(for door open only)
○ ○ ○ ○ ○
25: Position Detection 3(for door open only)
○ ○ ○ ○ ○
26: PG feedback error
○ ○ ○ ○ ○
27: output signal when unable to open the door
28: over torque (OT1)
These parameters can be used for external terminal output
Summary of Function Settings
Settings Functions Descriptions
0
No function MO has no function.
01
AC drive in operation The drive is ON when it receives voltage or operation command.
2
Zero speed frequency signal
(including STOP)
Zero speed output signals (including STOP).
3
AC drive ready
Active when the drive is ON and no abnormality detected or
abnormality is cleared.
4
Low voltage warning(Lv) Active when the detected input voltage is too low.
5
Fault indication Active when fault occurs.
6
Overhead warning (Pr.06.09)
A
ctive when IGBT or heat sink overheats to prevent OH turn off
the drive. When temperature higher than 85 = ON, lower than ℃
<80 = OFF℃ .
7
Detection of braking resistor
action level
Active when drive begins software braking, this signal can be
used as brake module VFDB action signal or indicator.
8
Warning indication Active when warning is detected.
9
Over voltage warning Active when over-voltage is detected.
- ''( 1
- 1
- Preface 2
- Table of Content 5
- Chapter 1 Introduction 7
- 1-1 Receiving and Inspection 8
- T02DD21A0 9
- Minimum Mounting Clearances 10
- CAUTION! 11
- Dimensions for Motor 12
- ECMD-B9160GMS 13
- Chapter 2 Wiring 14
- 2-1 Wiring Diagram 15
- Used with external power 16
- Not allowed 17
- 2-2 Main Circuit Terminal 18
- Chapter 2 Wiring 19
- 2-3 Control Circuit Terminal 20
- 3-1 Operation Method 23
- 3-2 Keypad Descriptions 24
- Chapter 4 Parameter Settings 25
- Settings 28
- Parameter Reset 48
- Start-up Display Selection 48
- Software version 49
- Password Input 49
- Password Set 49
- Control Method 50
- Door Control Mode 51
- Output Direction 52
- Demo Mode 53
- Frequency Testing Command 53
- Motor Auto Tuning (PM) 55
- Motor Auto Tuning (IM) 57
- Output Voltage 3 61
- Output Frequency 4 61
- Output Voltage 4 61
- OD:("OPEN":STOP) 62
- CD:(" OPEN": STOP) 62
- Multi-function Output (MO3) 65
- Digital Output Direction 66
- Position Detection Signal 1 66
- Encoder (PG) Signal Type 68
- Encoder pulse 68
- Encoder Input Type Setting 68
- Door Width Pulses (Unit:1) 70
- 04.19=S1 73
- 04.20=S2 73
- Freqeunc 73
- VFPG SVC FOCPG 74
- 05.19=S1 77
- 05.20=S2 77
- Door Re-open Detection Time 79
- Quadrant I 80
- Quadrant II 80
- Quadrant III 80
- Quadrant IV 80
- Low Voltage Level 81
- Position Control Mode 82
- VFPG SVC FOCPG FOCPM 84
- Auto Restart After Fault 85
- Gain for Speed Feed Forward 88
- VFPG SVC FOCPG FOCPM 89
- Communication Address 90
- Transmission Speed 90
- Transmission Fault Treatment 90
- Time-out Detection 90
- Communication Protocol 90
- Code Description: 91
- Status monitor 97
- Read only 97
- Example: 98
- Response Delay Time 99
- Multi-function Output RY1 103
- Multi-function Output RY2 103
- View User-defined Parameters 103
- 2 1 1B 104
- 111x16 + x16 =16+11 = 104
- Enter 2127 104
- Chapter 5 Troubleshooting 106
- 5-1 Over Current (oc) 107
- 5-2 Ground Fault (GFF) 108
- 5-3 Over Voltage (ov) 109
- 5-4 Low Voltage (Lv) 110
- 5-5 Over Heat (oH1) 111
- 5-6 Overload (oL) 112
- 5-8 Phase Loss (PHL) 114
- 5-9 Motor is not Running 115
- 5-12 Motor Run Error 118
- 5.14 Environmental Condition 120
- High Harmonic at Power Side 121
- Motor Temperature Rises 121
- 6.1.1 Reset 127
- Voltage 128
- Keypad 128
- Mechanical parts 128
- Main circuit 129
- Resistor of main circuit 130
- Control Characteristics 132
- Motor Model 134
- Appendix B 135
- B-1 Capacity Formulas 136
- Symbol explanation 137
- B-2 General Precautions 138
- Drives Selection 138
- Parameter Settings 138
- Standard motor 139
- Special motors: 140
- Power Transmission Mechanism 140
- Motor torque 141
© 2020, manymanuals.com. All rights reserved. | 1.011 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals