Delta 1.07 VFD-D D User Manual Page 78
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 Parameter Settings|DD Series
4-54
Door Close DC Brake Starting Frequency
Control mode VF VFPG SVC FOCPG
Factory setting: 0.00
Settings 0.00~120.00Hz
During the period AC motor drive decelerating to stop, this parameter sets the DC brake starting
frequency If Pr.05-24 is lower than Pr.01-09 (starting frequency), DC brake will regards lowest frequency
as starting frequency.
Door Re-open Current Level 1
Control mode VF VFPG SVC FOCPG FOCPM VF
Factory setting: 100.0
Settings 0.0~150.0% (AC drive’s rated current)
Door Re-open Current Level 1 for Acceleration Area
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 150
Settings 100~200% (100% is Pr.05-25 setting)
Door Re-open Current Level 1 for Low Speed Area
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 100.0
Settings 0.0~150.0%(Drive’s rated current)
Pr.05-25~05-27 is setting for door open/close curve set 1. When one of MI (Pr.02-01~02-05) is set to 25,
door open/close curve switch to 2nd set.
Door Re-open Current Level 2
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 100.0
Settings 0.0~150.0%(Drive’s rated current)
Door Re-open Current Level 2 for Acceleration Area
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 150
Settings 0.0~150.0% (Drive’s rated current)
Door Re-open Current Level 2 for Low Speed Area
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 100
Settings 100~200%(100% is the setting in Pr.05-29)
Pr.05-28~05-30 is setting for door open/close curve set 2. When one of MI (Pr.02-01~02-05) is set to 25,
door open/close curve switch to 2nd set.
Door Re-open Low Speed Boundary
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 2.0
Settings
1.0~99.0%(Total door width=100%; range between 0%~Pr.05.31 is excluded from lo
w
speed detection area)
Door Re-open Acceleration Boundary
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 70.0
Settings
8.0~97.0% (Total door width =100%; range between Pr.05.32~100% is the
acceleration area)
During the door close, it will re-close from the open complete position to the close complete position
when there is an obstacle (the stall current exceeds Pr. 05.25/05.26/05.28/05.29). Door close command
will be ignored when the drive is perform re-opening and will be valid again after door completely open is
reached.
Pr.05-33 sets the time for decelerating to 0 Hz when door close error occurs. It is recommended to set a
minimum value less than the current limit in order for door to re-open in shortest time to ensure
passenger’s safety.
- ''( 1
- 1
- Preface 2
- Table of Content 5
- Chapter 1 Introduction 7
- 1-1 Receiving and Inspection 8
- T02DD21A0 9
- Minimum Mounting Clearances 10
- CAUTION! 11
- Dimensions for Motor 12
- ECMD-B9160GMS 13
- Chapter 2 Wiring 14
- 2-1 Wiring Diagram 15
- Used with external power 16
- Not allowed 17
- 2-2 Main Circuit Terminal 18
- Chapter 2 Wiring 19
- 2-3 Control Circuit Terminal 20
- 3-1 Operation Method 23
- 3-2 Keypad Descriptions 24
- Chapter 4 Parameter Settings 25
- Settings 28
- Parameter Reset 48
- Start-up Display Selection 48
- Software version 49
- Password Input 49
- Password Set 49
- Control Method 50
- Door Control Mode 51
- Output Direction 52
- Demo Mode 53
- Frequency Testing Command 53
- Motor Auto Tuning (PM) 55
- Motor Auto Tuning (IM) 57
- Output Voltage 3 61
- Output Frequency 4 61
- Output Voltage 4 61
- OD:("OPEN":STOP) 62
- CD:(" OPEN": STOP) 62
- Multi-function Output (MO3) 65
- Digital Output Direction 66
- Position Detection Signal 1 66
- Encoder (PG) Signal Type 68
- Encoder pulse 68
- Encoder Input Type Setting 68
- Door Width Pulses (Unit:1) 70
- 04.19=S1 73
- 04.20=S2 73
- Freqeunc 73
- VFPG SVC FOCPG 74
- 05.19=S1 77
- 05.20=S2 77
- Door Re-open Detection Time 79
- Quadrant I 80
- Quadrant II 80
- Quadrant III 80
- Quadrant IV 80
- Low Voltage Level 81
- Position Control Mode 82
- VFPG SVC FOCPG FOCPM 84
- Auto Restart After Fault 85
- Gain for Speed Feed Forward 88
- VFPG SVC FOCPG FOCPM 89
- Communication Address 90
- Transmission Speed 90
- Transmission Fault Treatment 90
- Time-out Detection 90
- Communication Protocol 90
- Code Description: 91
- Status monitor 97
- Read only 97
- Example: 98
- Response Delay Time 99
- Multi-function Output RY1 103
- Multi-function Output RY2 103
- View User-defined Parameters 103
- 2 1 1B 104
- 111x16 + x16 =16+11 = 104
- Enter 2127 104
- Chapter 5 Troubleshooting 106
- 5-1 Over Current (oc) 107
- 5-2 Ground Fault (GFF) 108
- 5-3 Over Voltage (ov) 109
- 5-4 Low Voltage (Lv) 110
- 5-5 Over Heat (oH1) 111
- 5-6 Overload (oL) 112
- 5-8 Phase Loss (PHL) 114
- 5-9 Motor is not Running 115
- 5-12 Motor Run Error 118
- 5.14 Environmental Condition 120
- High Harmonic at Power Side 121
- Motor Temperature Rises 121
- 6.1.1 Reset 127
- Voltage 128
- Keypad 128
- Mechanical parts 128
- Main circuit 129
- Resistor of main circuit 130
- Control Characteristics 132
- Motor Model 134
- Appendix B 135
- B-1 Capacity Formulas 136
- Symbol explanation 137
- B-2 General Precautions 138
- Drives Selection 138
- Parameter Settings 138
- Standard motor 139
- Special motors: 140
- Power Transmission Mechanism 140
- Motor torque 141
© 2020, manymanuals.com. All rights reserved. | 1.638 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals