Delta 1.07 VFD-D D User Manual Page 83
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 Parameter Settings|DD Series
4-59
Times of Door Opened/Closed in Demo Mode (L)
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 0
Settings 0~9999
Times of Door Opened/Closed in Demo Mode (H)
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 0
Settings 0~9999
When executing demo mode, it records the number of times the door opened or closed. It counts as one
when door action from open to close.
Clear Demo Mode Door Open/Close Record
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 0
Settings
0: Disable
1: Clear (Pr.06.14 and Pr.06.15)
When Pr.06-16 is set to 1, door open/close counting will be cleared and reset to 0.
Present Fault Record
2nd Most Recent Fault Record
3rd Most Recent Fault Record
4th Most Recent Fault Record
5th Most Recent Fault Record
6
th
Sixth Most Recent Fault Record
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 00
Settings
0: No fault
1: Over-current during acceleration (ocA)
2: Over-current during deceleration (ocd)
3: Over-current during steady speed (ocn)
4: Reserved
5: Reserved
6:Over-current at stop (ocS)
7:Over voltage during acceleration (ovA)
8 Over voltage during deceleration (ovd)
9:Over voltage during steady speed (ovn)
10:Over voltage at stop (ovS)
11:Low voltage during acceleration (LvA)
12:Low voltage during deceleration (Lvd)
13:Low voltage during steady speed (Lvn)
14:Low voltage at stop (LvS)
15:Phase loss protection (PHL)
16:IGBT overheat (oH1)
17: Reserved
18:IGBT overheat protection circuit error (tH1o)
19~20: Reserved
21: 150% 1Min, AC drive overload (oL)
22:Motor overload (EoL1 )
23~29: Reserved
30: Memory write-in error (cF1)
31: Memory read-out error (cF2)
32: Isum current detection error (cd0)
33 U-phase current detection error (cd1)
34 V-phase current detection error (cd2)
35 W-phase current detection error (cd3)
Clamp current detection error (Hd0)
37 Over-current detection error (Hd1)
- ''( 1
- 1
- Preface 2
- Table of Content 5
- Chapter 1 Introduction 7
- 1-1 Receiving and Inspection 8
- T02DD21A0 9
- Minimum Mounting Clearances 10
- CAUTION! 11
- Dimensions for Motor 12
- ECMD-B9160GMS 13
- Chapter 2 Wiring 14
- 2-1 Wiring Diagram 15
- Used with external power 16
- Not allowed 17
- 2-2 Main Circuit Terminal 18
- Chapter 2 Wiring 19
- 2-3 Control Circuit Terminal 20
- 3-1 Operation Method 23
- 3-2 Keypad Descriptions 24
- Chapter 4 Parameter Settings 25
- Settings 28
- Parameter Reset 48
- Start-up Display Selection 48
- Software version 49
- Password Input 49
- Password Set 49
- Control Method 50
- Door Control Mode 51
- Output Direction 52
- Demo Mode 53
- Frequency Testing Command 53
- Motor Auto Tuning (PM) 55
- Motor Auto Tuning (IM) 57
- Output Voltage 3 61
- Output Frequency 4 61
- Output Voltage 4 61
- OD:("OPEN":STOP) 62
- CD:(" OPEN": STOP) 62
- Multi-function Output (MO3) 65
- Digital Output Direction 66
- Position Detection Signal 1 66
- Encoder (PG) Signal Type 68
- Encoder pulse 68
- Encoder Input Type Setting 68
- Door Width Pulses (Unit:1) 70
- 04.19=S1 73
- 04.20=S2 73
- Freqeunc 73
- VFPG SVC FOCPG 74
- 05.19=S1 77
- 05.20=S2 77
- Door Re-open Detection Time 79
- Quadrant I 80
- Quadrant II 80
- Quadrant III 80
- Quadrant IV 80
- Low Voltage Level 81
- Position Control Mode 82
- VFPG SVC FOCPG FOCPM 84
- Auto Restart After Fault 85
- Gain for Speed Feed Forward 88
- VFPG SVC FOCPG FOCPM 89
- Communication Address 90
- Transmission Speed 90
- Transmission Fault Treatment 90
- Time-out Detection 90
- Communication Protocol 90
- Code Description: 91
- Status monitor 97
- Read only 97
- Example: 98
- Response Delay Time 99
- Multi-function Output RY1 103
- Multi-function Output RY2 103
- View User-defined Parameters 103
- 2 1 1B 104
- 111x16 + x16 =16+11 = 104
- Enter 2127 104
- Chapter 5 Troubleshooting 106
- 5-1 Over Current (oc) 107
- 5-2 Ground Fault (GFF) 108
- 5-3 Over Voltage (ov) 109
- 5-4 Low Voltage (Lv) 110
- 5-5 Over Heat (oH1) 111
- 5-6 Overload (oL) 112
- 5-8 Phase Loss (PHL) 114
- 5-9 Motor is not Running 115
- 5-12 Motor Run Error 118
- 5.14 Environmental Condition 120
- High Harmonic at Power Side 121
- Motor Temperature Rises 121
- 6.1.1 Reset 127
- Voltage 128
- Keypad 128
- Mechanical parts 128
- Main circuit 129
- Resistor of main circuit 130
- Control Characteristics 132
- Motor Model 134
- Appendix B 135
- B-1 Capacity Formulas 136
- Symbol explanation 137
- B-2 General Precautions 138
- Drives Selection 138
- Parameter Settings 138
- Standard motor 139
- Special motors: 140
- Power Transmission Mechanism 140
- Motor torque 141
© 2020, manymanuals.com. All rights reserved. | 1.881 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals