Delta 36-240 Instruction Manual download pdf (Page 4)

CONNECTING TOOL TO POWER SOURCE

POWER CONNECTIONS

A separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should be

protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-

prong grounding type plugs and 3-hole receptacles which accept the tool’s plug. Before connecting the motor to the

power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same

characteristics as indicated on the tool. All line connections should make good contact. Running on low voltage will

damage the motor.

WARNING: DO NOT EXPOSE THE TOOL TO RAIN OR OPERATE THE TOOL IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your tool is wired for 120 volt, 60 HZ alternating current. Before connecting the tool to the power source, make sure

the switch is in the “OFF” position. The no-load speed of the motor is 5000 RPM.

GROUNDING INSTRUCTIONS

WARNING: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM

ELECTRIC SHOCK.

2. Grounded, cord-connected tools intended for use on

a supply circuit having a nominal rating less than 150

volts:

This tool is intended for use on a circuit that has an outlet

that looks like the one illustrated in Fig. AA. The tool has

a grounding plug that looks like the plug illustrated in Fig.

AA. A temporary adapter, which looks like the adapter

illustrated in Fig. BB, may be used to connect this plug to

a 2-hole receptacle as shown in Fig. BB if a properly

grounded outlet is not available. The temporary adapter

should be used only until a properly grounded outlet can

be installed by a qualified electrician. The green-colored

rigid ear, lug, and the like, extending from the adapter

must be connected to a permanent ground such as a

properly grounded outlet box. Whenever the adapter is

used, it must be held in place with a metal

screw.

NOTE: In Canada, the use of a temporary adapter is

not permitted by the Canadian Electric Code.

WARNING: IN ALL CASES, MAKE CERTAIN THE

RECEPTACLE IN QUESTION IS PROPERLY

GROUNDED. IF YOU ARE NOT SURE HAVE A

QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

1. All grounded, cord-connected tools:

In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electric current to

reduce the risk of electric shock. This tool is equipped

with an electric cord having an equipment-grounding

conductor and a grounding plug. The plug must be

plugged into a matching outlet that is properly installed

and grounded in accordance with all local codes and

ordinances.

Do not modify the plug provided - if it will not fit the outlet,

have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding

conductor can result in risk of electric shock. The

conductor with insulation having an outer surface that is

green with or without yellow stripes is the equipment-

grounding conductor. If repair or replacement of the

electric cord or plug is necessary, do not connect the

equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if

the grounding instructions are not completely

understood, or if in doubt as to whether the tool is

properly grounded.

Use only 3-wire extension cords that have 3-prong

grounding type plugs and 3-hole receptacles that accept

the tool’s plug, as shown in Fig. AA.

Repair or replace damaged or worn cord immediately.

40. DISCONNECT tool from power source and clean the machine before leaving it.

41. IMPORTANT: When the tool is not in use, the switch should be locked in the “OFF” position to prevent

unauthorized use.

42. MAKE SURE the work area is cleaned before leaving the machine.

43. SHOULD any part of your tool be missing, damaged, or fail in any way, or any electrical component fail to

perform properly, shut off switch and remove plug from power supply outlet. Replace missing, damaged or failed parts

before resuming operation.

44. ADDITIONAL INFORMATION regarding the safe and proper operation of this product is available from the National

Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201, in the Accident Prevention Manual for Industrial

Operations and also in the Safety Data Sheets provided by the NSC. Please also refer to the American National

Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machinery and the U.S. Department of Labor

OSHA 1910.213 Regulations.

1 2 3 4 5 6 7 8 9 ... 32 33

Comments to this Manuals

No comments

Delta 36-240 Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for Cordless chainsaws Delta 36-240