ELECTRIC POWER TOOLS
50
735
Single-Stage
Dust Collectors
Includes motor and blower, dust collec-
tion bags, support drum, 4" diameter
dust intake ports, intake port cap, base,
four swivel caster assemblies, cord and
plug, and instruction manual.
50-851
Order No. Mfg. No. HP Voltage
5029.01042 50-850 1-1/2 115V single phase
5029.01045 50-851 2 230V single phase
5029.01048 50-852 3 200V three phase
5029.01051 50-853 3 230V single phase
ACCESSORIES FOR MODEL 50-850
5029.01054 50-830 Dust bag, 1 micron, 2/pkg
ACCESSORIES FOR MODEL 50-851
5029.01057 50-832 Top dust bag, 1 micron
5029.01060 50-833 Bottom dust bag, 1 micron
5029.01063 50-834 3M short top bag, 1 micron, 2/pkg
ACCESSORIES FOR MODEL 50-852 & 50-853
5029.01066 50-836 Top dust bag, 1 micron
5029.01069 50-837 Bottom dust Bag, 1 micron
Roofing Nailer
Coil Wire Collation
7/8" to 1-3/4" x .120
• Steel body wear protectors
• Depth of drive adjustment for pre-
cision nailing
• Carbide tipped push lever to
reduce wear
• Rubber safety valve covering resists dirt, tar, etc.
• Single trip trigger mechanism – part no. 878226
Operating Air
Order No. Mfg. No. Pressure (psi) Nail Capacity Air Inlet (in)
5029.01030 NV45AB 70-120 120 3/8
Framing Nailer
Full Round Head Coil
Wire Collation
2" to 3-1/4" x .099/.113/.120/.131
• Built-in toenail push lever
• Depth-drive adjustment for
siding applications
• Open nose for ease of clearing jams
• Plastic shield to deflect wire collation
• Single trip trigger mechanism-part no. 876762
Operating Air
Order No. Mfg. No. Pressure (psi) Nail Capacity Air Inlet (in)
5029.01027 NV83A 70-120 200-300 3/8
Industrial Wet / Dry Vacuum
Motor Weight
Order No. Mfg. No. (amp) Voltage (lb)
5026.01033 KC-2010B 8 110V, 1 phase, 60 Hz 55
ACCESSORIES
5026.01036 KM-015 Filter
5026.01039 KM-016 Bag
• Automatic float shut-off prevents overflow
• Double filtration system
• Durable stainless steel tank
• Includes 8’ x 1-1/2’’ crushproof hose,
interlocking extension tubes, 16’’
floor brush attachment, 16’’
squeegee attachment and
heavy-duty caster
wheels for portability
• Tank Size: 10 gal
• Wet Capacity: 7-1/2 gal
• Air Flow: 83 ft
3
min
BagFilter
Cutting/Shaping Wheel
For cutting and shaping on soft and hard
woods, fibreglass, plastics and laminates.
• Do not use on metal
• Do not run in excess of 30,000 rpm
• Mandrel included
Fibreglass Reinforced
Cut-Off Wheels
For slicing and cutting metal, wood and
plastic. Cut easily through slot bolts,
screws, sheet metal, thin wood and plastics.
• Cut only along edge of cut-off wheels
• Do not attempt to sand or cut curved holes
• Diameter: 1-1/4"
• Thickness: .045"
Cut-Off Wheels
• Same as above except for
Thickness: .0625"
Order No. Mfg. No. Description
1099.90001 542 Cutting Shaping Wheel
1099.90004 426 Fiberglass Reinforced Cut-Off Wheels
1099.90007 540 Cut-Off Wheels
542
426
540
Comments to this Manuals