Delta 14-65l User Manual download pdf (Page 17)

17 - French

RÈGLES SPÉCIFIQUES ADDITIONNELLES DE SÛRETÉ

L’inobservation de ces règles peut conduire à des blessures graves.

CONSERVER CES DIRECTIVES.

Les consulter souvent et les utiliser pour donner des directives aux autres.

1. DO NOT OPERATE THIS MACHINE until it is completely

assembled and installed according to the instructions. A

machine incorrectly assembled can cause serious injury.

2. OBTAIN ADVICE from your supervisor, instructor, or

another qualified person if you are not thoroughly

familiar with the operation of this machine. Knowledge

is safety.

3. FOLLOW ALL WIRING CODES and recommended electrical

connections to prevent shock or electrocution.

4. SECURE THE MACHINE TO A SUPPORTING SURFACE.

Vibration can cause the machine to slide, walk, or tip over.

5. NEVER START THE MACHINE BEFORE CLEARING

THE TABLE OF ALL OBJECTS (tools, scrap pieces,

etc.). Debris can be thrown at high speed.

6. NEVER START THE MACHINE with the drill bit or

cutting tool against the workpiece. Loss of control of the

workpiece can cause serious injury.

7. PROPERLY LOCK THE DRILL BIT OR CUTTING TOOL IN

THE UNIT before operating this machine.

8. ADJUST the depth stop to avoid drilling into the table.

9. DO NOT attempt to mortise material that does not have

a flat surface, unless a suitable support is used.

10. USE ONLY DRILL BITS, CUTTING TOOLS, OR OTHER

ACCESSORIES with shank size recommended in your

instruction manual. The wrong size accessory can cause

damage to the machine and/or serious injury.

11. USE ONLY DRILL BITS OR CUTTING TOOLS that are

not damaged. Damaged items can cause malfunctions

that lead to injuries.

12. USE RECOMMENDED SPEEDS for all operations. Other

speeds may cause the machine to malfunction causing

damage to the machine and/or serious injury.

13. AVOID AWKWARD OPERATIONS AND HAND

POSITIONS. A sudden slip could cause a hand to move

into the bit.

14. KEEP ARMS, HANDS, AND FINGERS away from the

bit. Serious injury to the hand can occur.

15. ALWAYS position the holddown directly over the

workpiece to prevent the workpiece from lifting during

operation. Loss of control of the workpiece can cause

serious injury.

16. TURN THE MACHINE “OFF” AND WAIT FOR THE DRILL

BIT, CUTTING TOOL, OR SANDING DRUM TO STOP

TURNING prior to cleaning the work area, removing

debris, removing or securing work-piece, or changing

the angle of the table. A moving drill bit or cutting tool

can cause serious injury.

17. PROPERLY SUPPORT LONG OR WIDE work-pieces.

Loss of control of the workpiece can cause severe

injury.

18. NEVER PERFORM LAYOUT, ASSEMBLY OR SET-UP

WORK on the table/work area when the machine is

running. Serious injury can result.

19. TURN THE MACHINE “OFF”, disconnect the machine

from the power source, and clean the table/work area

before leaving the machine. LOCK THE SWITCH IN

THE “OFF” POSITION to prevent unauthorized use.

Someone else might accidentally start the machine and

cause serious injury to themselves.

20. ADDITIONAL INFORMATION regarding the safe

and proper operation of power tools (i.e. a safety

video) is available from the Power Tool Institute, 1300

Sumner Avenue, Cleveland, OH 44115-2851 (www.

powertoolinstitute.com). Information is also available

from the National Safety Council, 1121 Spring Lake

Drive, Itasca, IL 60143-3201. Please refer to the

American National Standards Institute ANSI 01.1 Safety

Requirements for Woodworking Machines and the U.S.

Department of Labor OSHA 1910.213 Regulations.

RACCORDEMENTS ÉLECTRIQUES

Un circuit électrique séparé doit être utilisé pour les machines. Les fils de ce circuit doivent être au moins de calibre 12. Ce circuitdoit

être protégé par un fusible temporisé de 20 A. Si on utilise un cordon prolongateur, ce cordon doit être à trois fils, avoir unefiche à trois

broches et une prise de courant à trois cavités, mise à la terre qui correspond à la fiche de la machine. Avant debrancher la machine,

s’assurer que l’interrupteur (les interrupteurs) se trouve(nt) en position « OFF » (ARRÊT) et que le courantélectrique présente les

mêmes caractéristiques que celles qui sont inscrites sur la machine. Toutes les connexions électriquesdoivent établir un bon contact.

Le fonctionnement sur une basse tension endommagera la machine.

Ne pas exposer la machine à la pluie, et ne pas l’utiliser dans des endroits humides.

INSTRUCTIONS DE MISE À LA TERRE

Cette machine doit être mise à la terre pendant son emploi, afin de protégerl’utilisateur des décharges

électriques.

SPÉCIFICATIONS DU MOTEUR

Cette machine est câblée pour un fonctionnement sur un courant alternatif de 120 volts 60 Hz. Avant de brancher la machine,

s’assurer que l’interrupteur se trouve à la position « OFF » (ARRÊT).

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 39 40

Comments to this Manuals

No comments

Delta 14-65l User Manual Page 17

Comments to this Manuals

Related products and manuals for Equipment Delta 14-65l