Delta 14-65l User Manual download pdf (Page 4)

4 - English

1. DO NOT OPERATE THIS MACHINE until it is completely

assembled and installed according to the instructions. A

machine incorrectly assembled can cause serious injury.

2. OBTAIN ADVICE from your supervisor, instructor, or

another qualified person if you are not thoroughly

familiar with the operation of this machine. Knowledge

is safety.

3. FOLLOW ALL WIRING CODES and recommended electrical

connections to prevent shock or electrocution.

4. SECURE THE MACHINE TO A SUPPORTING SURFACE.

Vibration can cause the machine to slide, walk, or tip over.

5. NEVER START THE MACHINE BEFORE CLEARING

THE TABLE OF ALL OBJECTS (tools, scrap pieces,

etc.). Debris can be thrown at high speed.

6. NEVER START THE MACHINE with the drill bit or

cutting tool against the workpiece. Loss of control of the

workpiece can cause serious injury.

7. PROPERLY LOCK THE DRILL BIT OR CUTTING TOOL IN

THE UNIT before operating this machine.

8. ADJUST the depth stop to avoid drilling into the table.

9. DO NOT attempt to mortise material that does not have

a flat surface, unless a suitable support is used.

10. USE ONLY DRILL BITS, CUTTING TOOLS, OR OTHER

ACCESSORIES with shank size recommended in your

instruction manual. The wrong size accessory can cause

damage to the machine and/or serious injury.

11. USE ONLY DRILL BITS OR CUTTING TOOLS that are

not damaged. Damaged items can cause malfunctions

that lead to injuries.

12. USE RECOMMENDED SPEEDS for all operations. Other

speeds may cause the machine to malfunction causing

damage to the machine and/or serious injury.

13. AVOID AWKWARD OPERATIONS AND HAND

POSITIONS. A sudden slip could cause a hand to move

into the bit.

14. KEEP ARMS, HANDS, AND FINGERS away from the

bit. Serious injury to the hand can occur.

15. ALWAYS position the holddown directly over the

workpiece to prevent the workpiece from lifting during

operation. Loss of control of the workpiece can cause

serious injury.

16. TURN THE MACHINE “OFF” AND WAIT FOR THE DRILL

BIT, CUTTING TOOL, OR SANDING DRUM TO STOP

TURNING prior to cleaning the work area, removing

debris, removing or securing work-piece, or changing

the angle of the table. A moving drill bit or cutting tool

can cause serious injury.

17. PROPERLY SUPPORT LONG OR WIDE work-pieces.

Loss of control of the workpiece can cause severe

injury.

18. NEVER PERFORM LAYOUT, ASSEMBLY OR SET-UP

WORK on the table/work area when the machine is

running. Serious injury can result.

19. TURN THE MACHINE “OFF”, disconnect the machine

from the power source, and clean the table/work area

before leaving the machine. LOCK THE SWITCH IN

THE “OFF” POSITION to prevent unauthorized use.

Someone else might accidentally start the machine and

cause serious injury to themselves.

20. ADDITIONAL INFORMATION regarding the safe

and proper operation of power tools (i.e. a safety

video) is available from the Power Tool Institute, 1300

Sumner Avenue, Cleveland, OH 44115-2851 (www.

powertoolinstitute.com). Information is also available

from the National Safety Council, 1121 Spring Lake

Drive, Itasca, IL 60143-3201. Please refer to the

American National Standards Institute ANSI 01.1 Safety

Requirements for Woodworking Machines and the U.S.

Department of Labor OSHA 1910.213 Regulations.

Failure to follow these rules may result in serious personal injury.

ADDITIONAL SPECIFIC SAFETY RULES

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should

be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have

3-prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the

machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of

the same characteristics as indicated on the machine. All line connections should make good contact. Running on low

voltage will damage the machine.

Do not expose the machine to rain or operate the machine in damp locations.

MOTOR SPECIFICATIONS

Your machine is wired for 120 Volt, 60 HZ alternating current. Before connecting the machine to the power source, make

sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

This machine must be grounded while in use to protect the operator from electric shock.

1 2 3 4 5 6 7 8 9 ... 39 40

Comments to this Manuals

No comments

Delta 14-65l User Manual Page 4

Comments to this Manuals

Related products and manuals for Equipment Delta 14-65l