Delta 36-L51L User Manual Page 19
- Page / 76
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
19
CROSS-CUTTING
Cross-cutting requires the use of the miter gauge to posi tion and guide the work. Before starting the cut, raise the blade so that it
is about 1/8” (3.2mm) higher than the top of the workpiece. Place the work against the miter gauge and advance both the gauge
and work toward the saw blade (Fig. 49 ). You can use the miter gauge in either table slot. Start the cut slowly and hold the work
firmly against the miter gauge and the table. Keep both hands on the miter gauge and workpiece. Do not touch the cut-off piece.
Feed the workpiece steadily through the blade until the workpiece is completely cut. Shift the workpiece slightly sideways away
from the blade, then pull the workpiece and miter guage back to the starting position. Remove the workpiece, then use a push
stick to push the cut-off piece past the blade and off the table before beginning the next cut.
For added safety and convenience, you can fit the miter gauge with an auxiliary wood-facing (C) Fig. 50 that should be at least
1 inch higher than the maximum depth of cut, and should extend out 12" or more to one side or the other depending on which
miter gauge slot is being used. This auxiliary wood-facing (C) can be fastened to the front of the miter gauge by using two wood
screws through the holes provided in the miter gauge body and into the wood-facing.
To use the guard properly:
1. Make sure the splitter is aligned with the blade
as described in the section “BLADE GUARD AND
SPLITTER ASSEMBLY AND ALIGNMENT.”
2. Replace or sharpen the anti-kickback pawls when they
become dull.
3. Keep the guard clean for visibility and free motion.
4. Do not use solvent or lubricants on the guard as they
may severely damage the plastic.
5. Use caution when feeding workpieces that may catch
on the guard and cause a bind or force the guard into
the blade (such as when cutting moulding).
Fig. 48
BLADE GUARD AND SPLITTER USE
The blade guard assembly provided with Delta saws (Fig. 48) must be used for all through-sawing operations.
The splitter prevents the kerf from closing and binding the blade, causing kickback. The anti-kickback pawls prevent the workpiece
and cut-off piece from being thrown back at the operator. The plastic guard prevents dust and debris from being thrown at the
operator.
Fig. 49
Fig. 50
C
When cross-cutting a number of pieces to the same length,
clamp a block of wood (B) to the fence and use it as a cut-
off gauge (Fig. 51). The block (B) must be at least 3/4" thick
to prevent the cut-off piece from binding between the blade
and the fence during removal from the saw table.
Always
position this block of wood in front of the saw blade. Once
the cut-off length is determined, lock the fence and use the
miter gauge to feed the work into the cut.
When using the block (B) Fig. 51 as a cut-off
gauge, it is very important that the rear end of the block be
positioned so the workpiece is clear of the block before it
enters the blade.
B
Fig. 51
Never use the fence as a cut-off gauge when cross-cutting.
- UNISAW sierra 1
- TABLE OF CONTENTS 2
- IMPORTANT SAFETY INSTRUCTIONS 2
- CALIFORNIA PROPOSITION 65 3
- GENERAL SAFETY RULES 4
- SAVE THESE INSTRUCTIONS 5
- POWER CONNECTIONS 6
- GROUNDING INSTRUCTIONS 6
- CARTON CONTENTS 7
- ASSEMBLY 8
- Fig. 3 Fig. 4 9
- Fig. 12 Fig. 13 11
- Fig. 24 Fig. 25 13
- OPERATION 14
- Fig. 39 Fig. 40 16
- MACHINE USE 18
- Fig. 51 19
- Fig. 48 19
- Fig. 49 19
- Fig. 50 19
- Fig. 52 20
- Fig. 53 Fig. 54 20
- Fig. 65 Fig. 66 23
- TROUBLESHOOTING 25
- MAINTENANCE 25
- ACCESSORIES 25
- WARRANTY 26
- FRANÇAIS 27
- RÈGLES DE SÉCURITÉ GÉNÉRALES 29
- CONSERVER CES DIRECTIVES 30
- CONTENUS DE BOITE 32
- FUNCTIONAL DESCRIPTION 32
- ASSEMBLAGE 33
- RALLONGES 34
- COUVERCLE DU MOTEUR 38
- FONCTIONNEMENT 39
- AJUSTEMENT DE LA TABLE 41
- CHANGEMENT DE LA LAME 42
- UTILISATION DE LA MACHINE 43
- DEPANNAGE 49
- ENTRETIEN 50
- ACCESSOIRIES 50
- GARANTIE 50
- PROPOSICIÓN DE CALIFORNIA 65 52
- NORMAS GENERALES DE SEGURIDAD 53
- MOTOR SPECIFICATIONS 55
- DESCRIPCIÓN FUNCIONAL 56
- CONTENIDO DE CARTON 56
- ENSAMBLAJE 57
- BASES DE EXTENSIÓN 58
- UTILIZAR LA MAQUINA 67
- Fig. 54 69
- MADERA”, y el uso 70
- MANTENIMIENTO 74
- LOCALIZACION DE FALLAS 74
- SERVICIO 74
- GARANTIA 75
- ACCESORIOS 75
- Delta Machinery 76
- 4825 Highway 45 North 76
- Jackson, TN 38305 76
- (800) 223-7278 76
Related products and manuals for Equipment Delta 36-L51L
Equipment Delta 31-260X User Manual
(60 pages)
(60 pages)
Equipment Delta 43-460 User Manual
(16 pages)
(16 pages)
Equipment Delta JT360 User Manual
(76 pages)
(76 pages)
Equipment Delta 78-960 User Manual
(12 pages)
(12 pages)
Equipment Delta A18657 User Manual
(54 pages)
(54 pages)
© 2020, manymanuals.com. All rights reserved. | 0.585 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals