Delta 36-L51L User Manual Page 6
- Page / 76
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
6
A separate electrical circuit should be used for your machines:
FOR SINGLE PHASE UNITS (EXCEPT THE FIVE HORSEPOWER): This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse.
FOR FIVE HORSEPOWER, SINGLE PHASE UNITS: The circuit should not be less than #10 wire and should be protected with a 40
Amp time lag fuse.
FOR PERMANENTLY CONNECTED MACHINES: See No. 3 in “GROUNDING INSTRUCTIONS”.
If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle
which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch is in the “OFF”
position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should
make good contact. Running on low voltage will damage the machine. (See “THREE PHASE OPERATION” and “LVC MAGNETIC
MOTOR CONTROL” sections for more information on power connections.)
Do not expose the machine to rain or operate the machine in damp locations.
1. All grounded, cord-connected machines:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric
shock. This machine is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be
plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an
outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord
or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to
whether the machine is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s
plug. Repair or replace damaged or worn cord immediately.
POWER CONNECTIONS
MOTOR SPECIFICATIONS
GROUNDING INSTRUCTIONS
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
All Unisaw motors are rated for 60 HZ alternating current, but voltage and HP varies according to model:
Model: Specifications:
36-L31, 36-L31X 3HP, 230V single phase motor
36-L51, 36-L51X, 36-L51L 5HP, 230V single phase motor
36-L53L 5 HP, 208-230V/460V three phase motor (Wired for 230V unless otherwise specified.)
Before connecting the machine to the power source, make sure that the switch is in the “OFF” position.
2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating between 150 - 250
volts, inclusive:
If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have
a grounding plug that looks like the plug illustrated in Fig. A. Make sure the machine is connected to an outlet having the same
configuration as the plug. No adapter is available or should be used with this machine. If the machine must be re-connected for
use on a different type of electric circuit, the re-connection should be made by qualified service personnel; and after re-connection,
the machine should comply with all local codes and ordinances.
NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.
In all cases, make certain that the receptacle in question is properly grounded. If you are not sure, have a qualified
electrician check the receptacle.
- UNISAW sierra 1
- TABLE OF CONTENTS 2
- IMPORTANT SAFETY INSTRUCTIONS 2
- CALIFORNIA PROPOSITION 65 3
- GENERAL SAFETY RULES 4
- SAVE THESE INSTRUCTIONS 5
- POWER CONNECTIONS 6
- GROUNDING INSTRUCTIONS 6
- CARTON CONTENTS 7
- ASSEMBLY 8
- Fig. 3 Fig. 4 9
- Fig. 12 Fig. 13 11
- Fig. 24 Fig. 25 13
- OPERATION 14
- Fig. 39 Fig. 40 16
- MACHINE USE 18
- Fig. 51 19
- Fig. 48 19
- Fig. 49 19
- Fig. 50 19
- Fig. 52 20
- Fig. 53 Fig. 54 20
- Fig. 65 Fig. 66 23
- TROUBLESHOOTING 25
- MAINTENANCE 25
- ACCESSORIES 25
- WARRANTY 26
- FRANÇAIS 27
- RÈGLES DE SÉCURITÉ GÉNÉRALES 29
- CONSERVER CES DIRECTIVES 30
- CONTENUS DE BOITE 32
- FUNCTIONAL DESCRIPTION 32
- ASSEMBLAGE 33
- RALLONGES 34
- COUVERCLE DU MOTEUR 38
- FONCTIONNEMENT 39
- AJUSTEMENT DE LA TABLE 41
- CHANGEMENT DE LA LAME 42
- UTILISATION DE LA MACHINE 43
- DEPANNAGE 49
- ENTRETIEN 50
- ACCESSOIRIES 50
- GARANTIE 50
- PROPOSICIÓN DE CALIFORNIA 65 52
- NORMAS GENERALES DE SEGURIDAD 53
- MOTOR SPECIFICATIONS 55
- DESCRIPCIÓN FUNCIONAL 56
- CONTENIDO DE CARTON 56
- ENSAMBLAJE 57
- BASES DE EXTENSIÓN 58
- UTILIZAR LA MAQUINA 67
- Fig. 54 69
- MADERA”, y el uso 70
- MANTENIMIENTO 74
- LOCALIZACION DE FALLAS 74
- SERVICIO 74
- GARANTIA 75
- ACCESORIOS 75
- Delta Machinery 76
- 4825 Highway 45 North 76
- Jackson, TN 38305 76
- (800) 223-7278 76
Related products and manuals for Equipment Delta 36-L51L
Equipment Delta 31-260X User Manual
(60 pages)
(60 pages)
Equipment Delta 43-460 User Manual
(16 pages)
(16 pages)
Equipment Delta JT360 User Manual
(76 pages)
(76 pages)
Equipment Delta 78-960 User Manual
(12 pages)
(12 pages)
Equipment Delta A18657 User Manual
(54 pages)
(54 pages)
© 2020, manymanuals.com. All rights reserved. | 1.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals