Delta A18657 User Manual Page 13
- Page / 54
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
13 - English
LEVELING TABLE EXTENSIONS
For optimum performance, level the table extensions,
A
B
C
E
Fig. 19
D
one of which is shown at (A) Fig. 19, with the
planer table. To check and adjust:
Disconnect machine from power
source!
1. Place a straight edge (B) Fig. 19 on the planer table
with one end of the straight edge extending out
over the infeed table extension (A). Check to see if
the table extension is level with the planer table on
both sides of table extension.
2. If an adjustment is necessary, loosen the locknut
(D) and adjust the stop screw (E) on each side of
the table (A). When they are level, tighten the locknut.
NOTE: If necessary, loosen the three screws (C), adjust the table extension, and tighten the screws (C).
3. Adjust the opposite side of the table extension (A).
4. Check and adjust other table extension.
ADJUSTING THE HEIGHT OF THE OUTFEED ROLLER
Disconnect machine from power source!
1. To check and adjust the outfeed roller, make a gauge
2"
51 mm
4"
101.6 mm
Fig. 20
4"
101.6 mm
1/4"
6.4 mm
3"
76.2 mm
1/2"
12.7 mm
block of hardwood. Follow the dimensions in Fig. 20.
2. Check the knives to be certain that they were inserted
correctly. See “REPLACING KNIVES.
3. Position the gauge block (A) Fig. 21 on the table
underneath the cutterhead. Insert a 0.020" (.5 mm)
feeler gauge on top of the gauge block.
4. Lower the head assembly and rotate the cutterhead
until one of the knives (B) touches the top of the feeler
gauge. NOTE: Pull the guard down (G, inset Fig. 21) to
gain access to the hex hole. Insert the supplied wrench
into the hex hole (F) and turn to rotate the cutterhead.
Tighten the cutterhead lock handle.
5. Remove the feeler gauge and move the gauge block
(A) Fig. 22 under one end of the outfeed roller (C). The bottom of the outfeed roller should touch the top of the
gauge block.
6. To adjust the outfeed roller, loosen the locknut (D) Fig. 22 and use a hex wrench to turn the adjusting screw (E)
until outfeed roller touches the gauge block (A). Tighten the locknut.
7. Repeat this adjustment on opposite side of the outfeed roller.
A
C
D
E
Fig. 22
A
Fig. 21
F
G
B
- Instruction Manual 1
- Manuel d’Utilisation 1
- Manual de Instrucciones 1
- TABLE OF CONTENTS 2
- IMPORTANT SAFETY INSTRUCTIONS 2
- CALIFORNIA PROPOSITION 65 3
- GENERAL SAFETY RULES 4
- SAVE THESE INSTRUCTIONS 5
- POWER CONNECTIONS 6
- MOTOR SPECIFICATIONS 6
- FUNCTIONAL DESCRIPTION 7
- CARTON CONTENTS 7
- ASSEMBLY 8
- CUTTERHEAD LOCK HANDLE 9
- CUTTERHEAD ADJUSTMENT HANDLE 9
- OPERATION 10
- ADJUSTING THE HEAD ASSEMBLY 11
- CUTTERHEAD LOCK 11
- SCALE AND POINTER 11
- SPEED CONTROL 11
- ADJUSTABLE INDEXING RING 12
- BLADE ZERO INDICATOR 12
- FULL RANGE DEPTH STOP 12
- LEVELING TABLE EXTENSIONS 13
- MACHINE USE 14
- RECOMMENDED DEPTH OF CUT 14
- OPERATING HINTS 14
- KNIFE TRANSFER TOOL STORAGE 14
- TROUBLESHOOTING 15
- MAINTENANCE 16
- LUBRICATION 18
- ACCESSORIES 19
- WARRANTY 19
- CONSERVEZ CES INSTRUCTIONS! 20
- RÈGLES DE SÉCURITÉ GÉNÉRALES 21
- CONSERVER CES DIRECTIVES 22
- RACCORDEMENTS ÉLECTRIQUES 23
- SPÉCIFICATIONS DU MOTEUR 23
- GROUNDING INSTRUCTIONS 23
- DESCRIPTION FONCTIONNELLE 24
- CONTENUS DE BOITE 24
- ASSEMBLAGE 25
- Français 26
- FONCTIONNEMENT 27
- RÉGLAGE DE L’ENSEMBLE DE TETE 28
- VERROUILLAGE DU PORTE-LAME 28
- ECHELLE ET POINTEUR 28
- COMMANDE DE VITESSE 28
- ANNEAU DE GUIDAGE RÉGLABLE 29
- INDICATEUR DE ZÉRO DE LA LAME 29
- UTILISATION DE LA MACHINE 30
- CONSEILS D’UTILISATION 31
- RANGEMENT DE LA CLÉ 31
- POIGNEES DE TRANSPORT 31
- BARRE DE TRANSFERT DES PIÈCES 31
- DEPANNAGE 32
- ENTRETIEN 32
- LUBRIFICATION 34
- LUBRIFIER LES CORPS DE PALIER 34
- ACCESSOIRIES 36
- GARANTIE 36
- PROPOSICIÓN DE CALIFORNIA 65 37
- NORMAS GENERALES DE SEGURIDAD 38
- GUARDE ESTAS INSTRUCCIONES 39
- ESPECIFICACIONES DEL MOTOR 40
- DESCRIPCIÓN FUNCIONAL 41
- CONTENIDO DE CARTON 41
- ENSAMBLAJE 42
- OPERACIÓN 44
- ESCALA E INDICADOR 45
- CONTROL DE VELOCIDAD 45
- INDICADOR DE CERO DE LA HOJA 46
- 101,6 mm 47
- 1/4 pulg 47
- UTILIZAR LA MAQUINA 48
- CONSEJOS DE UTILIZACIÓN 48
- LOCALIZACION DE FALLAS 49
- MANTENIMIENTO 49
- LUBRICACIÓN 51
- LUBRICAR EL COJINETE BLOQUEA 52
- SERVICIO 53
- GARANTIA 53
- Delta Machinery 54
- 4825 Highway 45 North 54
- Jackson, TN 38305 54
- (800) 223-7278 54
© 2020, manymanuals.com. All rights reserved. | 1.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals