Delta 36-L336 Use and Care Manual download pdf (Page 4)

Failure to follow these rules may result in serious personal injury.

ADDITIONAL SPECIFIC SAFETY RULES

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

Always use safety glasses. 1. Everyday eyeglasses are

not safety glasses. Also use face or dust mask if cutting

operation is dusty. All users and bystanders must always

wear certified safety equipment:

• ANSI Z87.1 Eye protection (CAN/CSA Z94.3)

• ANSI S12.6 (S3.19) Hearing protection

• NIOSH/OSHA/MSHA respiratory protection.

Do not expose to rain or use in damp locations.2.

3. Avoid awkward positions where a sudden slip could

cause a hand to move into a saw blade.

Never reach in back of, or around, the cutting tool 4. with

either hand to hold down the workpiece.

Keep arms, hands and fingers away 5. from the blade to

prevent serious injury.

Use a push stick that is appropriate to the application 6.

to push workpieces through the saw. A push stick is a

wooden or plastic stick, usually homemade, that should

be used whenever the size or shape of the workpiece

would cause you to place your hands within 6" (152 mm)

of the blade.

Use hold-downs, jigs, fixtures or feather boards to 7.

help guide and control the workpiece. Accessories for

use with your tool are available at extra cost from your

local dealer or authorized service center. Instructions for

making a push stick, a narrow rip auxiliary fence, a push

block and feather boards are included in this manual.

Do not perform ripping, crosscutting or any other 8.

operation freehand.

Stability9. . Make sure the table saw is firmly mounted to a

secure surface before use and does not move.

Never cut metals10. , cement board or masonry.

Certain man-made materials have special instructions

for cutting on table saws. Follow the manufacturer’s

recommendations at all times. Damage to the saw and

personal injury may result.

The proper throat plate must be in place at all times11.

to reduce the risk of a thrown workpiece and possible

injury.

Use the correct saw blade for the intended operation.12.

The blade must rotate toward the front of the saw. Always

tighten the blade arbor nut securely. Before use, inspect

the blade for cracks or missing teeth. Do not use a

damaged or dull blade.

Never attempt to free a stalled saw blade without first 13.

turning the machine off and disconnecting the saw

from the power source. If a workpiece or cut-off piece

becomes trapped inside the blade guard assembly, turn

saw off and wait for blade to stop before lifting the blade

guard assembly and removing the piece.

Never start the machine14. with the workpiece against

the blade to reduce the risk of a thrown workpiece

and personal injury.

Never have any part of your body in line with the path 15.

of the saw blade. Personal injury may occur.

Never perform layout, assembly or set-up work 16. on

the table/work area when the machine is running. A

sudden slip could cause a hand to move into the blade.

Severe injury can result.

Clean the table/work area before leaving the machine. 17.

Lock out the switch and disconnect from the power

source to prevent unauthorized use.

Do not leave a long board (or other workpiece) 18.

unsupported so the spring of the board causes

it to shift on the table resulting in loss of control

and possible injury. Provide proper support for the

workpiece, based on its size and the type of operation to

be performed. Hold the work firmly against the fence and

down against the table surface.

If your saw 19. makes an unfamiliar noise or if it vibrates

excessively, cease operating immediately, turn unit off

and disconnect from power source until the problem

has been located and corrected. Contact a DELTA

factory service center, a DELTA authorized service center

or other qualified service personnel if the problem can not

be found.

Use recommended accessories. 20. The use of improper

accessories may cause risk of personal injury.

Do not operate this machine21. until it is completely

assembled and installed according to the instructions.

A machine incorrectly assembled can cause serious injury.

Obtain advice 22. from your supervisor, instructor, or

another qualified person if you are not thoroughly

familiar with the operation of this machine. Knowledge

is safety.

Additional information 23. regarding the safe and proper

operation of power tools (i.e., a safety video) is available

from the Power Tool Institute, 1300 Sumner Avenue,

Cleveland, OH 44115-2851 (www.powertoolinstitute.com).

Information is also available from the National Safety

Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201.

Please refer to the U.S. Department of Labor OSHA

1910.213 Regulations.

1 2 3 4 5 6 7 8 9 ... 107 108

Comments to this Manuals

No comments

Delta 36-L336 Use and Care Manual Page 4

Comments to this Manuals