Delta 31-750 User Manual download pdf (Page 4)

ADDITIONAL SAFETY RULES

FOR RANDOM ORBITA L SANDERS

1. W ARNING: D O N O T operate your random orbit al

sander until it is completely assembled and inst alled

according to the instructions .

2.IF Y O U A R E N O T thoroughly familiar with the oper -

ation of the random orbit al sander , obt ain advice from

your supervisor, instructor or other qualified person.

3. USE FACE O R DUST MASK. WARNING: The dust

generated by cert ain woods and wood products can be

injurious to your health. A L W A Y S operate machinery in

well-ventilated areas and provide for proper dust removal.

U S E wood dust collection systems whenever possible .

Sanding of Lead-based p aint is NOT RECOMMENDED.

4. KEEP fingers away from rot ating abrasive disc.

5. MAKE SURE abrasive disc is not damaged and is

properly secured on the disc plate before operating.

6. NEVER perform layout, assembly or set-up work on

the t able while the sander is operating.

7. MAKE SURE workpiece is clear of abrasive disc

before turning unit on.

8. KEEP WORKAREA CLEAN. Cluttered areas can

create slipping or tripping hazards.

9. DON T FORCE TOOL. It will do the job better and

be safer at the rate for which it was designed.

10. NEVER use machine for wet sanding which can

create hazard of electrical shock.

11. U S E correctly sized abrasive disc. Maint ain minimum

table opening to keep fingers from being pinched or

workpiece being pulled down.

12. D O N O T sand near flammable liquids, vapors, or

gases.

13. A LW A Y S support workpiece on work t able. U S E sander

on a solid supporting surface where there is plenty of

room for handling and supporting workpiece.

14. CLEAR all debris from t able before sanding the

workpiece.

15. D O N O T use this sander to sand pieces too small

to be held safely and securely by hand.

16. ALWAYSWEARPROPER EYE PROTECTION.

17. T H E U S E of attachments and accessories not recom-

mended by Delt a may result in the risk of injuries.

18. PROTECT YOUREARS. W ear proper hearing pro -

tection.

19. AFTER turning of f power switch, disconnect tool

from power source and wait for sander to stop before

servicing.

20. D O N O T wear gloves, neckties, jewelry or loose

clothing.

21. MAINTAIN minimum clearance between abrasive

disc and fence.

22. AVOID KICKBACKS by sanding lef t of disc center ,

holding workpiece firmly, and using support fence when

possible.

23. KEEP hands and fingers out of dust chute.

24. D O N O T expose to rain or use in damp locations.

25. DISCONNECT MACHINE FROMPOWERSOURCE

BEFORE MAKING REPAIRS O R ADJUSTMENTS.

26. ADDITIONAL INFORMATION regarding the safe

and proper operation of this product is available from the

National Safety Council, 1121 Spring Lake Drive, It asca,

IL 60143-3201, in the Accident Prevention Manual for

Industrial Operations and also in the Safety Dat a Sheet s

provided by the NSC. Please also refer to the American

National Standards Institute ANSI 01.1 Safety Require-

m en t s for W oodworking Machinery and the U.S. D e part-

ment of Labor OSHA 1910.213 Regulations.

27. SAVE THESE INSTRUCTIONS.Refer to them of ten

and use them to instruct others.

UNPACKING A N D CLEANING

Your new random orbit al sander is shipped complete in one cont ainer . Carefully unp ack the sander and all loose items

from the shipping cont ainer . Clean all loose p art s. Fig. 2, illustrates the sander and all loose p art s supplied with the

machine. If you purchased the accessory Model 50-780 Stand, Fig. 3 illustrates the component s of the st and.

ASSEMBLY INSTRUCTIONS

W ARNING: F O R YOUR O W N SAFETY, DO NOT CONNECT THE SANDER TO A POWER SOURCE UNTIL T H E

MACHINE IS COMPLETELY ASSEMBLED AND YOU H AVE READ AND UNDERSTO O D THE ENTIRE OWNERS

MANUAL. NOTE: Place the machine on a firm supporting surface and proceed with the assembly instructions. If you

purchased the accessory 50-780 Steel S tand, this manual also cont ains instructions for it s assembly.

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Delta 31-750 User Manual Page 4

Comments to this Manuals

Related products and manuals for Grinding machines Delta 31-750