Delta ShopMaster SM500 User Manual download pdf (Page 5)

ADDITIONAL SPECIFIC SAFETY RULES

1. DO NOT OPERATE THIS MACHINE until it is

completely assembled and installed according to the

instructions. A machine incorrectly assembled can cause

serious injury.

2. OBTAIN ADVICE from your supervisor, instructor, or

another qualified person if you are not thoroughly

familiar with the operation of this machine. Knowledge is

safety.

3. FOLLOW A L L WIRING CODES and recommended

electrical connections to prevent shock or electrocution.

4. NEVER TURN THE MACHINE “ON” before clearing the

table/work area of all objects (tools, scraps of wood,

etc.). Flying debris is dangerous.

5. NEVER TURN THE MACHINE “ON” with the work-

piece contacting the abrasive surface. Kickback can

occur.

6. SECURE THE MACHINE to a supporting surface. Vibration

can cause the machine to slide, walk, or tip over.

7. COVER THE POWER TAKE-OFF SHAFT when not using

accessories. Unguarded rotating shafts can create an

entanglement hazard which can result in injury.

8. USE A DUST COLLECTION SYSTEM. Some types of

wood are known to cause disease or other health

problems.

9. FIRE HAZARD CLEAN THE MACHINE and dust collector

t h o r o u g h ly when processing different types of workpieces

(wood, steel, or aluminum). Combining wood and metal

dust can create an explosion or fire hazard. DO NOT

SAND OR POLISH MAGNESIUM. Fire will result.

10. PREVENT THE WORKPIECE from contacting the

sanding belt before starting the tool. Loss of control of

the workpiece is dangerous.

11. AVOID AW K W ARD OPERATIONS AND HAND

POSITIONS. A sudden slip could cause a hand to move

into the abrasive disc or belt.

12. M A I N TAIN A MAXIMUM CLEARANCE OF 1/16" between

the table and the abrasive disc or belt. The workpiece

could be drawn into the space between the abrasive disc

or belt and the table.

13. SUPPORT THE WORKPIECE firmly with a miter gauge,

backstop, or work table when sanding with a belt. Hold

the workpiece firmly. Loss of control of the workpiece can

result in injury.

14. AVOID KICKBACK by sanding in accordance with the

directional arrows. Feed the workpiece against the

downward rotation side of the disc or the forward rotation

of the belt. Loss of control of the workpiece can result in

i n j u r y.

15. DO NOT SAND very small or very thin workpieces that

cannot be safely controlled. Loss of control of the

workpiece can result in injury.

16. P R O P E R LY SUPPORT LONG OR WIDE W O R K P I E C E S .

Loss of control of the workpiece is dan-gerous.

17. NEVER PERFORM LAY O U T, A S S E M B LY, OR SET-UP

WORK on the table/work area when the machine is

running. A sudden slip could cause a hand to move into

the abrasive surface. Severe injury can result.

18. TURN THE MACHINE “OFF”, disconnect the machine

from the power source, and clean the table/work area

before leaving the machine. LOCK THE SWITCH IN

THE “OFF” POSITION to prevent unauthorized use.

Some-one else might accidentally start the machine and

cause injury to themselves.

19. ADDITIONAL INFORMATION regarding the safe and

proper operation of power tools (i.e. a safety video) is

available from the Power Tool Institute, 1300 Sumner

Avenue, Cleveland, OH 4411 5 - 2 8 5 1

( w w w.powertoolinstitute.com). Information is also

available from the National Safety Council, 1121 Spring

Lake Drive, Itasca, IL 60143-3201. Please refer to the

American National Standards Institute ANSI 01.1 Safety

Requirements for Woodworking Machines and the U.S.

Department of Labor OSHA 1910.213 Regulations.

READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO FOLLOW THESE

INSTRUCTIONS MAY RESULT IN ELECTRICAL SHOCK, FIRE AND / OR

SERIOUS INJURY.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

1 2 3 4 5 6 7 8 9 10 ... 67 68

Comments to this Manuals

No comments

Delta ShopMaster SM500 User Manual Page 5

Comments to this Manuals