Delta 22-785 Instruction Manual download pdf (Page 5)

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

ADDITIONAL SPECIFIC SAFETY RULES

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

1. DO NOT OPERATE THIS MACHINE until it is

completely assembled and installed according to

the instructions. A machine incorrectly assembled

can cause serious injury.

2. OBTAIN ADVICE from your supervisor, instructor,

or another qualified person if you are not

thoroughly familiar with the operation of this

machine. Knowledge is safety.

3. FOLLOW ALL WIRING CODES and recommend-

ed electrical connections to prevent shock or

electrocution.

4. KEEP KNIVES SHARP and free from rust and

pitch. Dull or rusted knives work harder and can

cause kickback.

5. NEVER TURN THE MACHINE “ON” before clearing

the table of all objects (tools, scraps of wood, etc.).

Flying debris can cause serious injury.

6. NEVER TURN THE MACHINE “ON” with the work-

piece contacting the cutterhead. Kickback can

occur.

7. SECURE THE MACHINE TO A SUPPORTING SUR-

FACE to prevent the machine from sliding, walking

or tipping over.

8. PROPERLY SECURE THE KNIVES IN THE CUTTER-

HEAD before turning the power “ON”. Loose

blades may be thrown out at high speeds causing

serious injury.

9. LOCK THE SPEED SETTING SECURELY before

feeding the workpiece through the machine.

Changing speeds while planing can cause kick-

back.

10. AVOID AWKWARD OPERATIONS AND HAND POSI-

TIONS. A sudden slip could cause a hand to move

into the knives.

11. KEEP ARMS, HANDS, AND FINGERS away from

the cutterhead, the chip exhaust opening, and the

feed rollers to prevent severe cuts.

12. NEVER REACH INTO THE CUTTERHEAD AREA

while the machine is running. Your hands can be

drawn into the knives.

13. DO NOT STAND IN LINE OF THE WORKPIECE.

Kickback can cause injury.

14. ALLOW THE CUTTERHEAD TO REACH FULL SPEED

before feeding a workpiece. Changing speeds

while planing can cause kickback.

15. WHEN PLANING BOWED STOCK, place the concave

(cup down) side of the stock on the table and cut

with the grain to prevent kickback.

16. DO NOT FEED A WORKPIECE that is warped,

contains knots, or is embedded with foreign

objects (nails, staples, etc.). Kickback can occur.

17. DO NOT FEED A SHORT, THIN, OR NARROW

WORKPIECE INTO THE MACHINE. Your hands can

be drawn into the knives and/or the workpiece can

be thrown at high speeds. See the “OPERATION”

section of this instruction manual for details.

18. DO NOT FEED A WORKPIECE into the outfeed end of

the machine. The workpiece will be thrown out of

the opposite side at high speeds.

19. REMOVE SHAVINGS ONLY with the power “OFF” to

prevent serious injury.

20. PROPERLY SUPPORT LONG OR WIDE WORK-

PIECES. Loss of control of the workpiece can cause

serious injury.

21. NEVER PERFORM LAYOUT, ASSEMBLY or set-up

work on the table/work area when the machine is

running. Serious injury will result.

22. TURN THE MACHINE “OFF”, DISCONNECT IT FROM

THE POWER SOURCE, and clean the table/work

area before leaving the machine. LOCK THE

SWITCH IN THE “OFF” POSITION to prevent un-

authorized use. Someone else might accidentally

start the machine and cause injury to themselves

or others.

23. ADDITIONAL INFORMATION regarding the safe

and proper operation of power tools (i.e. a safety

video) is available from the Power Tool Institute,

1300 Sumner Avenue, Cleveland, OH 44115-2851

(www.powertoolinstitute.com). Information is also

available from the National Safety Council, 1121

Spring Lake Drive, Itasca, IL 60143-3201. Please

refer to the American National Standards Institute

ANSI 01.1 Safety Requirements for Woodworking

Machines and the U.S. Department of Labor

Regulations.

1 2 3 4 5 6 7 8 9 10 ... 19 20

Comments to this Manuals

No comments

Delta 22-785 Instruction Manual Page 5

Comments to this Manuals