Delta 36-255L Instruction Manual

Browse online or download Instruction Manual for Mitre saws Delta 36-255L. Delta 36-255L Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - INSTRUCTION MANUAL

INSTRUCTION MANUALESPAÑOL: PÁGINA 25To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com.For Parts, Service, Warranty or o

Page 2 - IMPORTANT SAFETY INSTRUCTIONS

104. Attach the fence slide support (E) Fig. 7D, to theextension table (B) by using the two 5/16-18 x1 1/4”long hex head screws, 5/16” lockwashers and

Page 3 - CALIFORNIA PROPOSITION 65

11Fig. 11BFig. 10AAAAAFig. 9FASTENING MACHINE TO SUPPORTING SURFACEBefore operating your compound miter saw, firmly mountit to a workbench or other su

Page 4 - GENERAL SAFETY RULES

12Fig. 12ABFig. 13CDEB1. The compound miter saw will cut any angle from astraight 0° cut to 47° right and left. Turn locking knob(A) Fig. 12 countercl

Page 5

13Fig. 15CBFig. 16GFDAFig. 17AAADJUSTING FENCE 90° TO BLADEIMPORTANT: BEFORE MAKING THIS ADJUSTMENT,SET THE BLADE AT 0° TO THE TABLE. SEE SECTION“ADJU

Page 6 - GROUNDING INSTRUCTIONS

14Fig. 20Fig. 21BATILTING CUTTINGHEAD FOR BEVELCUTTINGIMPORTANT: MOVE THE SLIDING FENCE TO THELEFT TO PROVIDE CLEARANCE FOR THEBLADE AND GUARD. THE DE

Page 7 - FUNCTIONAL DESCRIPTION

15Fig. 24HCBFig. 25AFig. 26FEFig. 22Fig. 23BAAADJUSTING CHIP DEFLECTOR1. DISCONNECT THE MACHINE FROMTHE POWER SOURCE.2. A chip deflector (A) Fig. 22,

Page 8 - CARTON CONTENTS

16Fig. 27CABACDFig. 28Fig. 29ABCADJUSTING SLIDING FIT BETWEENTRUNNION AND BEVEL BRACKETAfter a long period of time, it may become necessary toadjust t

Page 9 - FENCE SLIDE

17The TwinLaser™laser units are mounted in a housing that isfitted into the upper blade guard of the miter saw (Fig. A). Thelasers project a beam of l

Page 10 - ATTACHING DUST BAG

18LEFT LASERADJUSTMENTSCREWFig. HFig. GFig. FTO CHECK FOR VERTICAL ALIGNMENT 1. The vertical alignment is set correctly when the linesdo not move hor

Page 11 - OPERATION

19CUTTING ALUMINUMAluminum extrusions (aluminum screens and stormwindows) can easily be cut with your miter saw. Whencutting aluminum extrusions, or o

Page 12 - FOR MITER SAW CUTTING

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

Page 13 - TABLE HAZARD ZONE

20Fig. 34Fig. 35CORRECTINCORRECTFig. 36CBACFor support when cutting long pieces, construct a worksupport extension. Fig. 36 illustrates the miter saw

Page 14 - ADJUSTING SLIDING FENCE

21CUTTING CROWN MOULDINGOne of the many features of the saw is the ease of cutting crown moulding. The following is an example of cutting bothinside a

Page 15 - ADJUSTING CHIP DEFLECTOR

22Fig. 41Fig. 42EBGCADHFig. 43FFig. 45BCFig. 44ACHANGING THE BLADEUSE ONLY CROSS-CUTTING SAWBLADES. DO NOT USE BLADES WITH DEEPGULLETS AS THEY CAN DEF

Page 16

23KEEP TOOL CLEANPeriodically blow out all air passages with dry compressed air. Clean all plastic parts with a soft damp cloth. NEVER usesolvents to

Page 18

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

Page 19 - MACHINE USE

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

Page 20 - WORK SUPPORT EXTENSIONS

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

Page 21 - OTHER ANGLES

5FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.1. DO NOT OPERATE THIS MACHINE UNTIL it isassembled and installed according to th

Page 22 - TROUBLESHOOTING

6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

Page 23 - WARRANTY

7EXTENSION CORDSUse proper extension cords. Make sureyour extension cord is in good condition and is a 3-wireextension cord which has a 3-prong ground

Page 24

8UNPACKING1. Carefully remove the machine from the carton.Retain all packing materials until you have inspectedand satisfactorily operated the machine

Page 25 - • DELTA)

9MOVING TABLE TO THE 0° CUT-OFFPOSITION1. Rotate locking knob (A) Fig. 6 counter-clockwise asfar as it will go. Depress lever (B) and rotate table (C)

Comments to this Manuals

No comments