INSTRUCTION MANUALUNISAW®10" Left Tilting Arbor Saw(Models 36-L31, 36-L51, 36-L53,36-L31X, 36-L51X)PART NO. 422-40-651-0017 - 05-16-03Copyright ©
10GPE ON / OFF SWITCH1. Locate the GPE switch and hardware that wasremoved in the section “EXTENSION WINGS.”2. Loosely assemble switch and switch brac
11Fig. 17 Fig. 18Fig. 19Fig. 21Fig. 204. If an adjustment is necessary, loosen two screws (F)Fig. 17, and adjust splitter bracket (A) until it is alig
12Fig. 23 Fig. 24Fig. 25Fig. 27Fig. 269. Insert the front end of splitter (P) Fig. 23, inside thesplitter mounting bracket behind splitter fastener pl
13Fig. 29Fig. 3013. Holding the clear blade guard, lower the saw bladeand assemble the table insert (E) Fig. 30, into the open-ing on the saw table.14
142. Place the motor cover (A) in the opening of theUnisaw as shown in Fig. 34. Place the rear motor coverclips inside the motor opening and push the
15OPERATING CONTROLS AND ADJUSTMENTSSTARTING AND STOPINGTHE SAWTo start the machine, push “ON” button (A) Fig. 39. Tostop the machine, push “OFF” butt
16ADJUSTING 90 AND 45DEGREE POSITIVE STOPSPositive stops are provided to quickly and accuratelyposition the blade at 90 and 45 degrees to the table. T
17ADJUSTING TABLE INSERTPlace a straight edge (B) across the table at both ends ofthe table insert as shown in Fig. 46. The table insert (A) should al
18OPERATIONSCommon sawing operations include ripping and crosscutting plus a few other standard operations of a fundamentalnature. As with all power m
19Fig. 53 Fig. 54Fig. 55Fig. 56Fig. 57USING THE UNIFENCE AS ACUT-OFF GAGEWHEN USING YOUR UNIFENCE SAWGUIDE® AS A CUT-OFF GAGE, MAKESURE IT IS PROPERLY
2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation
20stopped, unless it is a large piece allowing safe removal.When ripping boards longer than three feet, it isrecommended that a work support be used a
21Fig. 62Fig. 63WIMPORTANT: For certain cutting operations such asdadoing and moulding where you are not cuttingcompletely through the workpiece, the
22Fig. 66Fig. 67Fig. 68ABCUSING ACCESSORY DADO HEADTHE BLADE GUARD AND SPLITTERASSEMBLY CANNOT BE USED WHEN DADOING ORMOULDING AND MUST BE REMOVED OR
23STORAGEMITER GAGE HOLDER ANDWRENCH HOLDERThe miter gage and arbor wrenches can be stored in theslots provided in the motor cover, as shown in Fig. 7
24REPLACING BELTS ANDADJUSTING BELT TENSIONDISCONNECT MACHINE FROM POWERSOURCE.1. Remove motor cover to gain access to the motor.2. Place a block of w
25ACCESSORIESCONSTRUCTING AFEATHERBOARDFig. 80, illustrates dimensions for making a typicalfeatherboard. The material which the featherboard isconstru
26PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH 1
27PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P
The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder
31. FOR YOUR OWN SAFETY, READ THE INSTRUCT-TION MANUAL BEFORE OPERATING THEMACHINE. Learning the machine’s application,limitations, and specific hazar
4FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.ADDITIONAL SAFETY RULESFOR CIRCULAR SAWSSAVE THESE INSTRUCTIONS. Refer to them of
5A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding type plug a
7UNPACKING AND CLEANINGCarefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating fromall unpainte
8ASSEMBLYFOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE
9LVC STARTER BOX TO CABINETIf you purchased the machine with magnetic pushbutton electrical controls (LVC), the saw is shipped withthe starter box com
Comments to this Manuals