Delta 36-R53 Instruction Manual download pdf (Page 4)

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

ADDITIONAL SAFETY RULES

FOR CIRCULAR SAWS

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

1. DO NOT OPERATE THIS MACHINE until it is

assembled and installed according to the

instructions.

2. OBTAIN ADVICE FROM YOUR SUPERVISOR,

instructor, or another qualified person if you are

not familiar with the operation of this machine.

3. FOLLOW ALL WIRING CODES and recommended

electrical connections.

4. USE THE GUARDS WHENEVER POSSIBLE.

Check to see that they are in place, secured, and

working correctly.

5. AVOID KICKBACK by:

A. keeping blade sharp and free of rust and pitch.

B. keeping rip fence parallel to the saw blade.

C. using saw blade guard and spreader for every

possible operation, including all through

sawing.

D. pushing the workpiece past the saw blade prior

to release.

E. never ripping a workpiece that is twisted or

warped, or does not have a straight edge to

guide along the fence.

F. using featherboards when the anti-kickback

device cannot be used.

G. never sawing a large workpiece that cannot be

controlled.

H. never using the fence as a guide when

crosscutting.

I. never sawing a workpiece with loose knots or

other flaws.

6. ALWAYS USE GUARDS, SPLITTER, AND ANTI-

KICKBACK FINGERS whenever possible.

7. REMOVE CUT-OFF PIECES AND SCRAPS from

the table before starting the saw. The vibration of the

machine may cause them to move into the saw

blade and be thrown out. After cutting, turn the

machine off. After the blade has come to a

complete stop, remove all debris.

8. NEVER START THE MACHINE with the workpiece

against the blade.

9. NEVER run the workpiece between the fence and a

moulding cutterhead.

10. NEVER perform “free-hand” operations. Use either

the fence or miter gauge to position and guide the

workpiece.

11. HOLD THE WORKPIECE FIRMLY against the miter

gauge or fence.

12. USE PUSH STICK(S) for ripping a narrow

workpiece.

13. AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause a

hand to move into the blade.

14. KEEP ARMS, HANDS, AND FINGERS away from

the blade.

15. NEVER have any part of your body in line with the

path of the saw blade.

16. NEVER REACH AROUND or over the saw blade.

17. NEVER attempt to free a stalled saw blade without

first turning the machine “OFF”.

18. PROPERLY SUPPORT LONG OR WIDE

workpieces.

19. NEVER PERFORM LAYOUT, assembly or set-up

work on the table/work area when the machine is

running.

20. TURN THE MACHINE “OFF” AND DISCONNECT

THE MACHINE from the power source before

installing or removing accessories, before adjusting

or changing set-ups, or when making repairs.

21. TURN THE MACHINE “OFF”, disconnect the

machine from the power source, and clean the

table/work area before leaving the machine. LOCK

THE SWITCH IN THE “OFF” POSITION to prevent

unauthorized use.

22. ADDITIONAL INFORMATION regarding the safe

and proper operation of power tools (i.e. a safety

video) is available from the Power Tool Institute,

1300 Sumner Avenue, Cleveland, OH 44115-2851

(www.powertoolinstitute.com). Information is also

available from the National Safety Council, 1121

Spring Lake Drive, Itasca, IL 60143-3201. Please

refer to the American National Standards Institute

ANSI 01.1 Safety Requirements for Woodworking

Machines and the U.S. Department of Labor OSHA

1910.213 Regulations.

1 2 3 4 5 6 7 8 9 ... 27 28

Comments to this Manuals

No comments

Delta 36-R53 Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for Mitre saws Delta 36-R53