Delta 36-R53 Instruction Manual Page 6

  • Download
  • Add to my manuals
  • Print
  • Page
    / 28
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 5
6
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s
plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An
undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct
gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number,
the heavier the cord.
EXTENSION CORDS
FOREWORD
The Delta Unisaw is a 10" right tilting arbor saw. The Delta Unisaw features set the standards in the table saw industry.
A RIP FENCE ASSEMBLY IS NOT PACKAGED WITH THE PRODUCT. YOU MUST
INSTALL AND USE A
RIP FENCE SYSTEM FOR RIPPING OPERATIONS.
Fig. D
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere Total Length Gauge of
Rating Volts of Cord in Feet Extension Cord
0-6 240
up to
50 18 AWG
0-6 240 50-100 16 AWG
0-6 240 100-200 16 AWG
0-6 240 200-300 14 AWG
6-10 240
up to
50 18 AWG
6-10 240 50-100 16 AWG
6-10 240 100-200 14 AWG
6-10 240 200-300 12 AWG
10-12 240
up to
50 16 AWG
10-12 240 50-100 16 AWG
10-12 240 100-200 14 AWG
10-12 240 200-300 12 AWG
12-16 240
up to
50 14 AWG
12-16 240 50-100 12 AWG
12-16 240
GREATER THAN 100 FEET NOT RECOMMENDED
FUNCTIONAL DESCRIPTION
FIVE HORSEPOWER MOTORS
The motors supplied with single phase, 5 horsepower Unisaws are designed to be operated from a 220-240 volt power
system.
The 5 horsepower Unisaws are not supplied with a power cord. They must be permanently connected to the building
electrical system and grounded according to the National Electrical Code. Since they are permanently connected to
the building electrical system, extension cords cannot be used with the 5 horsepower Unisaw.
THREE PHASE OPERATION
Three phase Unisaws are not supplied with a power cord. They must be permanently connected to the building
electrical system and grounded according to the National Electrical Code. Since they must be permanently connected
to the building electrical system, extension cords cannot be used with three phase Unisaws.
MAGNETIC PUSH BUTTON CONTROLS
If you purchased the Unisaw with a magnetic starter, transformer and overload protection (LVC), refer to the separate
electrical instruction manual supplied with the machine. These Unisaws are not supplied with a power cord. They must
be permanently connected to the building electrical system and grounded according to the National Electrical Code.
These connections should be made by a qualified electrician. Since they must be permanently connected to the
building electrical system, extension cords cannot be used with these Unisaws.
NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT PRODUCTION
MODEL 36-R31. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY
NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND MAY BE INTENDED
TO ILLUSTRATE TECHNIQUE ONLY.
Page view 5
1 2 3 4 5 6 7 8 9 10 11 ... 27 28

Comments to this Manuals

No comments