Delta 14-070 Instruction Manual Page 11

  • Download
  • Add to my manuals
  • Print
  • Page
    / 18
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 10
CAUTION: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC
SHOCK.
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insu-
lation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary, do not connect the equipment grounding conductor to a live ter-
minal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded. Use only 3-wire extension cords that have 3-prong grounding type
plugs and 3-hole receptacles that accept the tool's plug.
Repair or replace damaged or worn cord immediately.
GROUNDING INSTRUCTIONS
110-120 VOLT OPERATION
As received, your drill press is ready-to-run for 110-120 volt
operation. This drill press, when wired for 110-120 volts,
is intended for use on a circuit that has an outlet and a plug
that looks like the one shown in Fig. 13. A temporary adapter,
which looks like the adapter illustrated in Fig. 14, may be
used to connect this plug to a 2-pole receptacle, as shown in
Fig. 14 if a properly grounded outlet is not avail-able. The
temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician.
THIS ADAPTER IS NOT APPLICABLE IN CANADA. The
green-colored rigid ear, lug, and the like, extending from the
adapter must be connected to a
permanent ground, such as a properly grounded outlet box,
as shown in Fig. 14.
220-240 VOLT OPERATION
Your drill press may be converted for 220-240 volt
operation.
The conversion of your drill press for 220-240 volt operation
must be done by qualified electrical personnel. Should you
desire to have your drill press converted for 220-240 volt
operation take your drill press to your local Authorized Delta
Service Center. You can phone 800-438-2486 for the location
of the nearest Authorized Service Center.
When converted for 220-240 volt operation, your drill press is
intended for use on a circuit that has an outlet like the one
illustrated in Fig. 14A. After conversion for 220-240 volts, the
drill press will have a grounding plug that looks like the plug
illustrated in Fig. 14A.
Make sure the drill press is connected to an outlet having the
same configuration as the plug. No adapter is available or
should be used when the drill press is converted for 220-240
volts. If the drill press must be reconnected for use on a dif-
ferent type of electrical circuit, the reconnection should be
made by qualified service personnel; and after reconnection,
the tool should comply with all local codes and ordinances.
Fig. 14A
230 VOLT
CURRENT-CARRYING PRONGS
GROUND PRONG
Fig. 13
Fig. 14
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
GROUNDED OUTLET BOX
GROUNDING
MEANS
ADAPTER
HOLES
HOLES
Page view 10
1 2 ... 6 7 8 9 10 11 12 13 14 15 16 17 18

Comments to this Manuals

No comments