Delta 17-925 User Manual

Browse online or download User Manual for Power drills Delta 17-925. delta accessory model 17-935 (or 17-924 kit)

  • Download
  • Add to my manuals
  • Print
  • Page
    / 20
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Part No. A18608 - 05-25-06
DELTA ACCESSORY
MODEL 17-935 (OR 17-924 KIT)
MORTISING ATTACHMENT
CARTON CONTENTS
Mortising Attachment Assembled
1. Fence
2. Locking Levers (2)
3. Flat washers (2)
4. T-Nuts
5. Guides
6. Hold-Down Assembly
7. Hold-Down Shaft
8. 5/32" Hex Wrench
9. Quill Alignment Pin
10. Chisel Holder
11. (4) Bushings
12. Carrying Case (For Model 17-924 Mortising
Attachment Kit ONLY)
13. Set of Chisels and Bits (4) - 1/4", 5/16", 3/8",
and 1/2" (Furnished with Model 17-924 Mortising
Attachment Kit ONLY)
SELECTING A BUSHING
To select a bushing, match the proper size bush-
ing with the quill size of your drill press. See chart
below.
Quill Bushing
Size Thickness
50.8 mm 7.5 mm
52 mm 6.9 mm
55 mm 5.4 mm
60 mm 2.9 mm
66 mm No bushing
ASSEMBLY
IMPORTANT: Use the correct bushings as indicated in the carton contents for your machine. The Delta 16-1/2" drill
presses (Model 17-900 and DP400) do not require bushings.
INTRODUCTION
The 17-935 (17-924 kit) Mortising Attachment converts your drill press into an accurate mortising machine and can be
used with drill presses that have the following quill diameters: 50.8mm, 52mm, 55mm, 60mm and 66mm.
12
10
11
13
9
8
7
1
2
4
5
6
3
Fig. A
Page view 0
1 2 3 4 5 6 ... 19 20

Summary of Contents

Page 1 - MORTISING ATTACHMENT

Part No. A18608 - 05-25-06DELTA ACCESSORYMODEL 17-935 (OR 17-924 KIT)MORTISING ATTACHMENTCARTON CONTENTSMortising Attachment Assembled1. Fence2. Locki

Page 2 - ASSEMBLING THE CHISEL HOLDER

10PARA PRENSAS DE TALADRO DELTA DE 381 MM (15”) Y MODELOS 17-925 Y 17-965 (PRENSAS DE TALADRO DE VELOCIDAD VARIABLE DE 419,1 MM [16 ½”])1. Coloque y

Page 3

11LAS SIGUIENTES INSTRUCCIONES CORRESPONDEN A LAS PRENSAS DE TALADRO DE VELOCIDAD VARIABLE DE 381 MM (15”) Y AL MODELO 17-925 DE 419,1 MM (16-1/2”).Aj

Page 4

12Coloque la pieza de trabajo sobre la mesa y ajuste la altura de la mesa de manera que la punta del cincel libere la pieza por 12,7 mm (½”). Baje el

Page 5

13Part No. A15816 - 12-01-05ACCESSOIRE DELTAMODÈLE 17-935 (OU TROUSSE 17-924)ACCESSOIRE POUR MORTAISEAssemblage de l’accessoire pour mortaiseIMPORTANT

Page 6 - OPERATION

14Fig. 1Fig. 2Fig. 3Fig. 4Fig. 5Fig. 6ABC DDABBDGDECFDHKLMAASSEMBLAGE DU PORTE-BÉDANE1. Visser lâchement la poignée (A, fi g. 1) dans le bas du trou p

Page 7 - ACCESORIOS DELTA

15LES DIRECTIVES SUIVANTES SONT POUR LES PRESSES À COLONNE UTILITAIRES DELTA DE 15 PO (38,1 CM)Débrancher la machine de la source d’alimentation.1. A

Page 8

16POUR LES PRESSES À COLONNE UTILITAIRES DELTA DE 15 PO (38,1 CM) ET LES MODÈLES 17-925 ET 17-965 (PRESSES À COLONNE DE 161/2 PO (42 CM) À RÉGIME VARI

Page 9

17LES DIRECTIVES SUIVANTES SONT POUR LES PRESSES À COLONNE UTILITAIRES DE 15 PO (38,1 CM) ET LES PRESSES À COLONNE DE 161/2 PO (42 CM) À RÉGIME VARIAB

Page 10 - AJUSTE DE LA GUÍA A LA MESA

18VITESSES DE BROCHELa vitesse de broche correcte varie selon la dimension de la mèche et la dureté du bois. Les meilleures coupes s’effectuent normal

Page 12 - OPERACIÓN

2ASSEMBLING THE CHISEL HOLDER1. Loosely thread the knob (A) Fig. 1 into the bottom of the hole of the chisel holder (B) (See Fig. 2).2. Install the

Page 13 - ACCESSOIRE POUR MORTAISE

20 Delta Machinery 4825 Highway 45 NorthJackson, TN 38305www.deltamachinery.com

Page 14 - ASSEMBLAGE DU PORTE-BÉDANE

3Disconnect the machine from the power source.THE FOLLOWING INSTRUCTIONS ARE FOR THE DELTA 15" UTILITY DRILL PRESSES.1. Lower the spindle (A) Fi

Page 15

4THE FOLLOWING INSTRUCTIONS ARE FOR THE DELTA 17-900 16-1/2" DRILL PRESS.Disconnect the machine from the power source.NOTE: This unit requires NO

Page 16 - Fig. 11B

5THE FOLLOWING INSTRUCTIONS ARE FOR THE 15" UTILITY AND MODEL 17-925 16-1/2" VARIABLE SPEED DRILL PRESSES. Attach the fence (A) Fig. 14 to

Page 17

6SPINDLE SPEEDSThe correct spindle speed depends on the size of the bit and the hardness of the wood. Your best cuts are generally in the range of 650

Page 18 - FONCTIONNEMENT

7Part No. A15816 - 12-01-05ACCESORIOS DELTAMODELO 17-935 (O JUEGO 17-924)DISPOSITIVO PARA HACER MORTAJASCONTENIDO DE CARTONDispositivo para hacer mort

Page 19

8MONTAJE DEL SOPORTE PARA CINCEL1. Enrosque suavemente la perilla (A) Fig. 1 en la parte inferior del orifi cio del soporte para cincel (B) (Vea Fig.

Page 20 - Jackson, TN 38305

9LAS SIGUIENTES INSTRUCCIONES CORRESPONDEN A LAS PRENSAS DE TALADRO DELTA DE 381 MM (15”).Desconecte la máquina de la fuente de alimentación.1. Baje

Comments to this Manuals

No comments