4
THE FOLLOWING INSTRUCTIONS ARE FOR THE DELTA 17-900 16-1/2" DRILL PRESS.
Disconnect the machine from the power source.
NOTE: This unit requires NO bushings for attaching the chisel holder to the quill.
1. Insert and lock the smaller diameter end of the alignment pin (A)
Fig. 12 into the spindle.
2. Slide the chisel holder (B) Fig. 12 over the alignment pin and over
the stop collar (C) of the drill press.
NOTE: Face the slot (D) in the chisel holder (B) toward the front of the
drill press.
3. Tighten the thumb screw (F) Fig. 12 on the alignment pin first, then
tighten the locking lever (E).
NOTE: The locking lever is spring-loaded. Change it by pulling out
and repositioning the hub of the lever on the nut located directly
under the hub.
4. Loosen the thumb screw (E) and remove the alignment pin (A) from
the spindle.
ATTACHING THE FENCE TO THE TABLE
THE FOLLOWING INSTRUCTIONS ARE FOR THE 10", 12", 14", AND 32" RADIAL DRILL PRESSES AND THE
MODEL 17-900.
Attach the fence (A) Fig. 13 to the drill press table with two
locking levers (C and Y), flat washers (D) and T-nuts (E).
IMPORTANT: The T-nuts are positioned under the drill press
table.
NOTE: For ease of assembly, you can remove the locking
levers (C) and (Y) from the studs (F) by removing the screws and
springs (B). Attach the studs (F) first, then re-attach the lever
(Y) to the stud (F). You can reposition the locking levers (C) and
(Y) by lifting the upward and rotating them on the stud in either
direction.
D
C
A
F
B
E
D
C
A
F
B
Y
E
Fig. 13
Fig. 12
Disconnect the machine from the power source.
FOR DELTA 15” UTILITY DRILL PRESSES AND
MODELS 17-925 AND 17-965 (16-1/2” VARIABLE
SPEED DRILL PRESSES)
1. Install and lock smaller diameter end of alignment pin
(H) into spindle (A). Refer to Fig. 5.
2. Assemble the largest inside diameter split-ring
bushings (J) Fig. 11A, around the quill and under
stop collar (G). IMPORTANT. FOR MODEL NO.
17-965 DRILL PRESS, USE THE INTERMEDIATE
SIZED SPLIT-RING BUSHINGS. THE BUSHINGS
ARE TO BE POSITIONED AROUND THE SMALLER
DIAMETER OF THE QUILL.
3. While holding the split-ring bushings (J) Fig. 11A,
in position on the quill, slide chisel holder (K) over
alignment pin (H) and over split-ring bushings (J).
IMPORTANT. Before tightening locking lever (L) Fig.
11B, make certain the slot in split-ring bushings (J)
Fig. 11A, lines up with slot in chisel holder (K) Fig.
11B. Tighten thumb screw (M) onto alignment pin (H).
Tighten locking lever (L) around split-ring bushings.
NOTE: Locking lever (L) is spring-loaded and can be
repositioned by pulling out lever and repositioning
the hub of lever on the nut located directly under the
hub.
4. After chisel holder (K) Fig. 11B, is assembled to
the machine, loosen thumb screw (M), and remove
alignment pin (H) from spindle. Proceed with
“ASSEMBLING FENCE TO TABLE.”
Fig. 11A
Fig. 11B
G
A
J
H
K
K
L
M
H
(68 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals