Delta 22-790X Instruction Manual download pdf (Page 4)

Failure to follow these rules may result in serious personal injury.

ADDITIONAL SPECIFIC SAFETY RULES

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

1. DO NOT OPERATE THIS MACHINE until it is

completely assembled and installed according to the

instructions. A machine incorrectly assembled can

cause serious injury.

2. OBTAIN ADVICE from your supervisor, instructor,

or another qualified person if you are not thoroughly

familiar with the operation of this machine. Knowledge

is safety.

3. FOLLOW ALL WIRING CODES and recommend-

ed electrical connections to prevent shock or

electrocution.

4. KEEP KNIVES SHARP and free from rust and pitch.

Dull or rusted knives work harder and can cause

kickback.

5. NEVER TURN THE MACHINE “ON” before clearing the



debris can cause serious injury.

6. NEVER TURN THE MACHINE “ON” with the work- piece

contacting the cutterhead. Kickback can occur.

7. SECURE THE MACHINE TO A SUPPORTING SUR-

FACE to prevent the machine from sliding, walking or

tipping over.

8. PROPERLY SECURE THE KNIVES IN THE CUTTER-

HEAD before turning the power “ON”. Loose blades

may be thrown out at high speeds causing serious

injury.

9. LOCK THE SPEED SETTING SECURELY before feeding

the workpiece through the machine. Changing speeds

while planing can cause kick-back.

10. AVOID AWKWARD OPERATIONS AND HAND POSI-

TIONS. A sudden slip could cause a hand to move

into the knives.

11. KEEP ARMS, HANDS, AND FINGERS away from the

cutterhead, the chip exhaust opening, and the feed

rollers to prevent severe cuts.

12. NEVER REACH INTO THE CUTTERHEAD AREA while

the machine is running. Your hands can be drawn into

the knives.

13. DO NOT STAND IN LINE OF THE WORKPIECE.

Kickback can cause injury.

14. ALLOW THE CUTTERHEAD TO REACH FULL SPEED

before feeding a workpiece. Changing speeds while

planing can cause kickback.

15. WHEN PLANING BOWED STOCK, place the concave



the grain to prevent kickback.

16. DO NOT FEED A WORKPIECE that is warped, contains

       

staples, etc.). Kickback can occur.

17. DO NOT FEED A SHORT, THIN, OR NARROW

WORKPIECE INTO THE MACHINE. Your hands can be

drawn into the knives and/or the workpiece can be

thrown at high speeds. See the Operation section of

this instruction manual for details.

18. DO NOT FEED A WORKPIECE into the outfeed end of

the machine. The workpiece will be thrown out of the

opposite side at high speeds.

19. REMOVE SHAVINGS ONLY with the power “OFF” to

prevent serious injury.

20. PROPERLY SUPPORT LONG OR WIDE WORK-PIECES.

Loss of control of the workpiece can cause serious

injury.

21. NEVER PERFORM LAYOUT, ASSEMBLY or set-up work

on the table/work area when the machine is running.

Serious injury will result.

22. TURN THE MACHINE “OFF”, DISCONNECT IT FROM

THE POWER SOURCE, and clean the table/work area

before leaving the machine. LOCK THE SWITCH IN

THE “OFF” POSITION to prevent un-authorized use.

Someone else might accidentally start the machine

and cause injury to themselves or others.

23. ADDITIONAL INFORMATION regarding the safe and

    

is available from the Power Tool Institute, 1300

     

powertoolinstitute.com). Information is also available

from the National Safety Council, 1121 Spring Lake

Drive, Itasca, IL 60143-3201. Please refer to the

American National Standards Institute ANSI 01.1

Safety Requirements for Woodworking Machines and

the U.S. Department of Labor Regulations.

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be

protected with a time delay fuse. NOTE: Time delay fuses should be marked “D” in Canada and “T” in the US. If an extension

cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will



and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should

make good contact. Running on low voltage will damage the machine.

Do not expose the machine to rain or operate the machine in damp locations.

MOTOR SPECIFICATIONS

Your machine is wired for 240 volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure

the switch is in the “OFF” position.

1 2 3 4 5 6 7 8 9 ... 71 72

Comments to this Manuals

No comments

Delta 22-790X Instruction Manual Page 4

Comments to this Manuals

Related products and manuals for Power planers Delta 22-790X