Delta TP400LS Instruction Manual

Browse online or download Instruction Manual for Power planers Delta TP400LS. Delta TP400LS Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 21
  • Table of contents
  • BOOKMARKS
  • Rated4.5 / 5. Based on6 customer reviews
Page view 0
INSTRUCTION MANUAL
12½" Portable Planer
(Model TP400LS)
PART NO. A02473 - 04-06-04
Copyright © 2004 Delta Machinery
ESPAÑOL: PÁGINA 21
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Page view 0
1 2 3 4 5 6 ... 20 21

Summary of Contents

Page 1 - 12½" Portable Planer

INSTRUCTION MANUAL12½" Portable Planer(Model TP400LS)PART NO. A02473 - 04-06-04Copyright © 2004 Delta MachineryESPAÑOL: PÁGINA 21To learn more ab

Page 2 - GENERAL SAFETY RULES

10FASTENING PLANER TO STAND2. Fasten cutterhead raising and lowering handle (A)Fig. 8, to shaft using the M5x.8x20mm hex socket headscrew (C) with wre

Page 3

11STARTING ANDSTOPPING PLANERThe on/off switch (A) Fig. 14, is located on the front ofthe planer motor. To turn the machine “ON” move theswitch up to

Page 4 - Refer to them often

12RECOMMENDEDDEPTH OF CUTNOTE: One revolution of the raising and lowering handlewill move the cutterhead up or down 3/32 of an inch.A 3/32" depth

Page 5 - GROUNDING INSTRUCTIONS

13KNIFE TRANSFER TOOLSTORAGE1. The knife transfer tool (A) Fig. 20, supplied with yourplaner, can easily be stored underneath the outfeedtable extensi

Page 6 - EXTENSION CORDS

14Fig. 22 Fig. 23CARRYING HANDLE/STOCK TRANSFER BAR1. Your planer is provided with a foam covered carrying handle (A) Fig. 22, located on top of the m

Page 7 - UNPACKING AND CLEANING

155. Figure 26 illustrates the cutterhead (C) locked inplace allowing access to the knife locking bar (E).6. Using the supplied wrench (E) Fig. 27, un

Page 8 - ASSEMBLY

169. Remove knife transfer tool and tighten the sixscrews, five of which are shown at (F) Fig. 30, usingwrench (E) supplied. 10. Replace other knife b

Page 9

17Fig. 34Fig. 352. Make sure the knives are inserted into the cutterheadproperly, as explained under “REPLACING KNIVES.”3. Place the gage block (A) Fi

Page 10 - FASTENING PLANER TO STAND

18MAINTENANCEBRUSH INSPECTIONAND REPLACEMENTDISCONNECT MACHINE FROM POWERSOURCE.Brush life varies. It depends on the load on the motor.Check the brush

Page 11

19NOTES

Page 12 - TABLE EXTENSIONS

2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

Page 13 - WRENCH STORAGE

20A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,and Delta Authorized Service Stat

Page 14 - REPLACING KNIVES

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

Page 15

3GENERAL SAFETY RULES1. FOR YOUR OWN SAFETY, READ THE INSTRUCTIONMANUAL BEFORE OPERATING THE MACHINE.Learning the machine’s application, limitations,

Page 16 - OF OUTFEED ROLLER

4ADDITIONAL SAFETY RULES FOR PLANERS1. DO NOT OPERATE THIS MACHINE until it iscompletely assembled and installed according tothe instructions. A machi

Page 17 - OPERATION

5A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

Page 18 - LUBRICATION

6EXTENSION CORDSUse proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong groun

Page 19

7FOREWORDFUNCTIONAL DESCRIPTIONUNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container. Peel protective fi

Page 20 - ACCESSORIES

FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE IN

Page 21 - • DELTA)

9Fig. 4Fig. 5Fig. 6AAABCALOWERINGEXTENSION TABLESThe infeed and outfeed table extensions (A) Fig. 4, areshipped attached to the machine in the “UP” po

Comments to this Manuals

No comments