Delta 11-990 Instruction Manual

Browse online or download Instruction Manual for Power tools Delta 11-990. Delta 11-990 Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 15
  • Table of contents
  • BOOKMARKS
  • Rated4.5 / 5. Based on17 customer reviews
Page view 0
INSTRUCTION MANUAL
12" Bench Drill Press
(Model 11-990)
PART NO. 903709 (018)
Copyright © 2001 Delta Machinery
ESPAÑOL: PÁGINA 17
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Page view 0
1 2 3 4 5 6 ... 14 15

Summary of Contents

Page 1 - 12" Bench Drill Press

INSTRUCTION MANUAL12" Bench Drill Press(Model 11-990)PART NO. 903709 (018)Copyright © 2001 Delta MachineryESPAÑOL: PÁGINA 17To learn more about D

Page 2 - GENERAL SAFETY RULES

1013. IMPORTANT: Make certain the spindle taper (Q) Fig.17, and tapered hole in chuck (R) are clean and free ofany grease, lacquer or rust preventive

Page 3 - FOR DRILL PRESSES

11STARTING AND STOPPINGDRILL PRESSThe switch (A) Fig. 21, is located on the front of the drillpress head. To turn the drill press “ON” move the switch

Page 4 - GROUNDING INSTRUCTIONS

123. The table can be tilted right or left by pulling out andremoving table alignment pin (C) Fig. 25, and looseningtable locking bolt (D). NOTE: If p

Page 5 - OPERATING INSTRUCTIONS

13Fig. 30CB5. After the belt is positioned on the desired steps ofthe motor and spindle pulleys, pivot motor away from thedrill press head until the b

Page 6

14OPERATIONThe following directions will give the inexperiencedoperator a start on common drill press operations. Usescrap material for practice to ge

Page 7 - ASSEMBLY

15Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which

Page 8

2GENERAL SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain ha

Page 9

3ADDITIONAL SAFETY RULES FORFOR DRILL PRESSES1. DO NOT operate your tool until it is completelyassembled and installed according to the instructions.2

Page 10

4POWER CONNECTIONSA separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should beprotected wi

Page 11

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cordwhich has a 3-prong grounding type plug a

Page 12 - ADJUSTING BELT TENSION

6WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE TOOL TO THE POWER SOURCE UNTIL THEMACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE EN

Page 13 - RETURN SPRING

7ASSEMBLY1. Assemble the column (A) Fig. 3, to the base (B) usingthe four M8x25mm hex head screws (C), three of whichare shown. Loosen set screw (D) a

Page 14 - BORING IN WOOD

84. Slide raising rack (F) Fig. 7, table and table bracketonto drill press column, as shown. Make sure bottom ofraising rack (F) Fig. 8, is engaged wi

Page 15 - ACCESSORIES

99. Figure 13, illustrates the table raising and loweringhandle (K) assembled to worm gear shaft (G).10. Thread clamp handle (M) Fig. 14, into hole in

Comments to this Manuals

No comments