Delta 17-965 Instruction Manual download pdf (Page 7)

You can have your drill press converted to 230 volt

operation.

A qualified electrician must perform this conversion. Should

you desire to have your drill press converted for 230 volt

operation, take your drill press to your local Authorized

Delta Service Center. You can call 800-223-7278 for the

location of the nearest Authorized Service Center.

When converted for 230 volt operation, your drill press is

intended for use on a circuit that has an outlet like the one

illustrated in Fig. C. After conversion to 230 volts, the drill

press will have a grounding plug that looks like the plug

illustrated in Fig. C.

Make sure the drill press is connected to an outlet having

the same configuration as the plug. No adapter is available

or should be used when the drill press is converted for 230

volts. If the drill press must be reconnected for use on a

different type of electrical circuit, the re-connection should

be made by qualified service personnel; and after re-

connection, the tool should comply with all local codes and

ordinances.

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

EXTENSION CORDS

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension

cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using

an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a

drop in line voltage, resulting in loss of power and overheating. Fig. D-1 or D-2, shows the correct gauge to use depending

on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

Fig. D-1

Fig. D-2

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge of

Rating Volts of Cord in Feet Extension Cord

0-6 120

up to

25 18 AWG

0-6 120 25-50 16 AWG

0-6 120 50-100 16 AWG

0-6 120 100-150 14 AWG

6-10 120

up to

25 18 AWG

6-10 120 25-50 16 AWG

6-10 120 50-100 14 AWG

6-10 120 100-150 12 AWG

10-12 120

up to

25 16 AWG

10-12 120 25-50 16 AWG

10-12 120 50-100 14 AWG

10-12 120 100-150 12 AWG

12-16 120

up to

25 14 AWG

12-16 120 25-50 12 AWG

12-16 120

GREATER THAN 50 FEET NOT RECOMMENDED

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge of

Rating Volts of Cord in Feet Extension Cord

0-6 240

up to

50 18 AWG

0-6 240 50-100 16 AWG

0-6 240 100-200 16 AWG

0-6 240 200-300 14 AWG

6-10 240

up to

50 18 AWG

6-10 240 50-100 16 AWG

6-10 240 100-200 14 AWG

6-10 240 200-300 12 AWG

10-12 240

up to

50 16 AWG

10-12 240 50-100 16 AWG

10-12 240 100-200 14 AWG

10-12 240 200-300 12 AWG

12-16 240

up to

50 14 AWG

12-16 240 50-100 12 AWG

12-16 240

GREATER THAN 100 FEET NOT RECOMMENDED

Fig. C

3. Grounded, cord-connected machines intended for

use on a supply circuit having a nominal rating

between 150 - 250 volts, inclusive:

1 2 3 4 5 6 7 8 9 10 11 12 ... 16 17

Comments to this Manuals

No comments

Delta 17-965 Instruction Manual Page 7

Comments to this Manuals

Related products and manuals for Power tools Delta 17-965