Delta 28-195 Instruction Manual

INSTRUCTION MANUAL10" Band Saw(Model 28-195)PART NO. 902127 (0112)Copyright © 2001 Delta MachineryESPAÑOL: PÁGINA 23To learn more about DELTA MAC

10ASSEMBLING TABLEALIGNMENT SCREWInsert M6 x 30mm button head bolt (A) Fig. 11, downthrough hole in table, as shown, and place a M6 flatwasher (C) ont

11STARTING ANDSTOPPING SAWThe switch (A) Fig. 17, is located on the front side of theband saw. To turn the saw “ON” move the switch (A) tothe up posit

12TRACKING THE BLADEFor accurate work and maximum blade life, it is important that the blade (A) Fig. 20, be centered on the upper bandsaw wheel. When

13Fig. 22Fig. 23Fig. 24ADJUSTING UPPER BLADE GUIDESAND BLADE SUPPORT BEARINGThe blade guides must be properly adjusted to prevent the blade from twist

14ADJUSTING LOWER BLADE GUIDESAND BLADE SUPPORT BEARINGThe lower blade guides and blade support bearing should be adjusted at the same time as the upp

15Fig. 27Fig. 28Fig. 29Fig. 30TILTING THE TABLEThe table can be tilted 48 degrees to the right andapproximately 3 degrees to the left. To tilt the tab

Fig. 31Fig. 32Fig. 33Fig. 34ADJUSTING UPPERBLADE GUIDE ASSEMBLYThe upper blade guide assembly (A) Fig. 31, shouldalways be set about 1/8 above or as c

17Fig. 35Fig. 36Fig. 37Fig. 38MINIMUM CUTTING RADIUSTurning radius may vary depending on the type of bladeand amount of set. Each blade, however, depe

18Fig. 39Fig. 40Fig. 41Fig. 42WRENCH STORAGEThe hex wrench (A) supplied with your band saw can bestored inside the wheel cover, as shown in Fig. 39.DU

19Fig. 43An ideal accessory for use with your band saw is the28-196 Rip Fence, shown in Fig. 43. It can be movedalong the table surface by loosening l

2GENERAL SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain ha

20Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

3ADDITIONAL SAFETY RULES FORBAND SAWSWARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.SAVE THESE INSTRUCTIONS.Refer to the

4POWER CONNECTIONSA separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cordwhich has a 3-prong grounding type plug a

6Fig. 2For Fig. 21 - Band Saw2 - Table3 - Miter Gage4 - Table InsertFor mounting machine to stand5 - M8 x 35mm hex head bolts (4)6 - M8 flat washers (

7Fig. 3For Fig. 31 - Stand legs (4)2 - Upper braces for stand (2), 10-3/4"3 - Upper braces for stand (2), 13-9/16"4 - Lower braces for stand

8ASSEMBLINGSTAND AND FEET1. Assemble the stand, as shown in Fig. 4, using the32 M8x20mm Carriage head screws, 3/8" flat washersand M8 hex nuts su

9ASSEMBLING TABLETO MACHINE1. Slide table (A) Fig. 7, into position on band sawtrunnions, as shown.Fig. 72. Line up the four threaded holes in bottom