Delta 28-206 Instruction Manual

Browse online or download Instruction Manual for Power tools Delta 28-206. Delta 28-206 Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 24
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
INSTRUCTION MANUAL
14" Band Saws
(Models 28-206, 28-276)
PART NO. 906452 - 08-16-02
Copyright © 2002 Delta Machinery
ESPAÑOL: PÁGINA 25
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
MODEL 28-206
SHOWN
Page view 0
1 2 3 4 5 6 ... 23 24

Summary of Contents

Page 1 - 14" Band Saws

INSTRUCTION MANUAL14" Band Saws(Models 28-206, 28-276)PART NO. 906452 - 08-16-02Copyright © 2002 Delta MachineryESPAÑOL: PÁGINA 25To learn more a

Page 2 - GENERAL SAFETY RULES

10Fig. 814. Align the holes in the base (A) Fig. 8, with the holesin the two sides (B).15. Insert a M8x1.25x16mm hex head flange screwthrough the hole

Page 3 - SAVE THESE INSTRUCTIONS

11MODEL 28-276 OPEN STAND ASSEMBLYWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEMBLE

Page 4 - GROUNDING INSTRUCTIONS

1214. Align the four holes in the short brace (A) Fig. 14,with the four holes in the two legs (B).15. Insert a M8x1.25x16mm carriage head bolt through

Page 5 - OPERATING INSTRUCTIONS

13BAND SAW ASSEMBLYWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ

Page 6 - BAND SAW PARTS

14ATTACHING THE TABLE TOTHE SAWFig. 191. Remove the band saw blade.2. Align the two table studs (A) Fig. 19, in the bottom ofthe table, with the two h

Page 7

15OPERATING CONTROLS AND ADJUSTMENTSSTARTING ANDSTOPPING SAWThe power switch is located on the left side of themachine. To turn the machine “ON”, push

Page 8 - MODEL 28-276 OPEN STAND PARTS

16ADJUSTING THE TABLE STOPThe tool is equipped with an adjustable table stop (A)Fig. 26 that allows the table to be set at 90 degrees tothe blade.Tilt

Page 9

17TRACKING THE BLADECAUTION: DISCONNECT MACHINE FROM POWERSOURCE.IMPORTANT: Before tracking the blade, make sure thatthe blade guides and blade suppor

Page 10

185. Two set screws (B) Fig. 35 hold the upper bladeguides (A) in place. Loosen the set screws (B) to movethe guides (A). Place them as close as possi

Page 11

19OPERATIONSBefore starting the machine, insure that all adjustments are properly made and the guards are in place. Turn the upperwheel by hand to mak

Page 12

2GENERAL SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain ha

Page 13 - BAND SAW ASSEMBLY

20TROUBLESHOOTING GUIDEIn spite of how well a band saw is maintained, problems can occur. The following troubleshootingguide will help you solve the m

Page 14 - TABLE INSERT

21Trouble: BLADE WILL NOT TRACK.Probable Cause Remedy1. Blade too loose 1. Adjust tension2. Upper wheel not properly adjusted. 2. Adjust upper wheel.3

Page 15 - “OFF” POSITION

22BAND SAW BLADESA band saw blade is a delicate piece of steel that is subjected to tremendous strain. You canobtain long use from a band saw blade if

Page 17

Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin

Page 18 - DUST PORT

3ADDITIONAL SAFETY RULES FORBAND SAWSWARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.SAVE THESE INSTRUCTIONS.Refer to the

Page 19 - OPERATIONS

4POWER CONNECTIONSA separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected

Page 20 - TROUBLESHOOTING GUIDE

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord whichhas a 3-prong grounding type plug a

Page 21

6BAND SAW PARTSFig. 21. Band Saw2. Motor3. Table4. Table Insert5. Belt6. Motor Mounting Plate7. M8x1.25x80mm (4) (for assembling saw to stand)1234568.

Page 22 - BAND SAW BLADES

7MODEL 28-206 ENCLOSED STAND PARTS1. Base (2)2. Side (2)3. Stand Top4. Door (2)5. Pulley Guard6. M8x1.25x100mm Hex Head Screw7. M8x1.25x16mm Hex Head

Page 23

8MODEL 28-276 OPEN STAND PARTS1. Legs (4)2. Stand Top3. Long Brace (2)4. Short Brace (2)5. Upper Pulley Guard 6. Lower Pulley Guard7. M8x1.25x80mm Hex

Page 24 - Two Year Limited Warranty

9MODEL 28-206 ENCLOSED STAND ASSEMBLYWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEM

Comments to this Manuals

No comments