Delta 31-280 Instruction Manual

Browse online or download Instruction Manual for Power tools Delta 31-280. Delta 31-280 Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 16
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
INSTRUCTION MANUAL
Sanding Center
6" Belt/12" Disc Sander
(Model 31-280)
PART NO. 406-12-651-0004 - 07-31-01)
Copyright © 2001 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Page view 0
1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - (Model 31-280)

INSTRUCTION MANUALSanding Center6" Belt/12" Disc Sander(Model 31-280)PART NO. 406-12-651-0004 - 07-31-01)Copyright © 2001 Delta MachineryTo

Page 2

ADJUSTING BELT SANDER TABLE MITER GAUGE SLOTPARALLEL TO SANDING BELT1. DISCONNECT TOOL FROM POWER SOURCE.2. Position the table (Figs. 25 and 26) 90 de

Page 3 - MOTOR SPECIFICATIONS

11Fig. 28Fig. 27Fig. 26Fig. 25CHANGING POSITION OF SANDING ARM1. The sanding arm (A) can be used in the vertical position (Fig. 27), the horizontal p

Page 4 - GROUNDING INSTRUCTIONS

12Fig. 31Fig. 30Fig. 32TILTING THE DISC SANDER TABLEThe table (A) can be tilted 45 degrees up (Fig. 31), or 45 degrees down (Fig. 32), by loosening th

Page 5 - CHANGING VOLTAGE

13ADJUSTING SANDING DISC GUARD1. DISCONNECT TOOL FROM POWER SOURCE.2. Adjust the sanding disc guard (A) Fig. 35, so that the front edge of the guard i

Page 6 - OPERATING INSTRUCTIONS

POWER TAKE-OFF SHAFT1. DISCONNECT TOOL FROM POWER SOURCE.2. A power take-off shaft is provided on the lower end ofthe sanding belt arm to accommodate

Page 7

1515ACCESSORIESA complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,and Delta Authorized

Page 8 - ATTACHING DUST CHUTE

16The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER®,INNOVATION THAT WORKS®, JET

Page 9 - THE SANDING BELT

2GENERAL SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are cer-tain

Page 10

3ADDITIONAL SAFETY RULES FOR SANDING CENTER1. WARNING: Do not operate this tool until assembly and installation are complete, according to instruction

Page 11

44Fig. 1 Fig. 2GROUNDED OUTLET BOXCURRENTCARRYINGPRONGSGROUNDING BLADEIS LONGEST OF THE 3 BLADESGROUNDED OUTLET BOXGROUNDINGMEANSADAPTERGROUNDING INST

Page 12 - SANDING DISC

25Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cordwhich has a 3-prong grounding type plug

Page 13 - ACCESSORY HOLDER

6ASSEMBLY INSTRUCTIONSWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWERSOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED, AND YOU R

Page 14 - REPLACING SANDING DISC

7Fig. 9ATTACHINGSANDING DISCCAUTION: DISCONNECT TOOL FROM POWER SOURCE.1. Clean the sanding disc plate (A) Fig. 9 of any oil orgrease, and be certain

Page 15 - Two Year Limited Warranty

8OPERATING CONTROLS AND ADJUSTMENTSSTARTING AND STOPPING THE TOOLThe on-off switch (A) Fig. 14 is located on the sander base. To turn the sander “ON”,

Page 16 - • DELTA)

9Fig. 17Fig. 16IMPORTANT: THE TOOL IS SHIPPED WITHOUT BELT TENSION. BEFORE OPERATING THE TOOL, ADJUST THE BELTFOR CORRECT TENSION AND PROPER TRACKING

Comments to this Manuals

No comments