Delta 31-390 Instruction Manual

Browse online or download Instruction Manual for Power tools Delta 31-390. Delta 31-390 Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 16
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
INSTRUCTION MANUAL
6" Edge Sander
(Model 31-390, 391, 392)
PART NO. 406-11-651-0006 - 03-12-02
Copyright © 2002 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Page view 0
1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - 6" Edge Sander

INSTRUCTION MANUAL6" Edge Sander(Model 31-390, 391, 392)PART NO. 406-11-651-0006 - 03-12-02Copyright © 2002 Delta MachineryTo learn more about DE

Page 2 - GENERAL SAFETY RULES

STARTING AND STOPPING EDGESANDERTo start the tool, push the start button (A) Fig. 25; to stopthe tool, push stop button (B).ADJUSTING TABLE POSITIONTo

Page 3 - Refer to them often

ADJUSTING LONG PLATENTo adjust the long platen when sanding on the straighttable:1. DISCONNECT TOOL FROM POWER SOURCE.2. Remove the top guard and dust

Page 4 - GROUNDING INSTRUCTIONS

ADJUSTING BELT TRACKINGTo check and adjust the tracking of the sanding belt onthe pulleys, proceed as follows:1. Raise the dust chutes (A) Fig. 34, at

Page 5 - EXTENSION CORDS

EDGE SANDINGWhen edge sanding, it is advisable to raise one end ofthe table as shown in Fig. 36. This allows cooler beltrunning, prevents spot wear, r

Page 6 - ASSEMBLY

CHANGING SANDING BELTSTo remove and install sanding belts, proceed as follows:1.DISCONNECT TOOL FROM POWER SOURCE.2. The sanding belt can be changed w

Page 7 - DUST CHUTE ASSEMBLY

15Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which

Page 8 - DRIVE PULLEY

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER®,INNOVATION THAT WORKS®, JETST

Page 9

2GENERAL SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain ha

Page 10 - ADJUSTING SHORT PLATEN

ADDITIONAL SAFETY RULES FORABRASIVE FINISHING MACHINES1. DO NOT OPERATE THIS MACHINE UNTIL it isassembled and installed according to the instructions.

Page 11 - ADJUSTING AUXILIARY END TABLE

4POWER CONNECTIONSA separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should beprotected wi

Page 12 - ADJUSTING PULLEY ALIGNMENT

Fig. AFUNCTIONAL DESCRIPTIONFOREWORDDelta Model 31-390 is a large capacity Edge Sander for fast, efficient, straight and bevel edge sanding with the a

Page 13 - OPERATIONS

6ASSEMBLING LEGS TO EDGESANDERCarefully assemble the two support legs to the base ofthe edge sander as follows:1. Fasten each support leg (C) Fig. 3,

Page 14 - MAINTENANCE

ASSEMBLING BELT TENSION LEVERAssemble the belt tension lever (A) Fig. 7, to thetensioning mechanism by threading the end of lever (B)into the tapped h

Page 15 - Two Year Limited Warranty

ASSEMBLING AUXILIARY ABRASIVEDRUM AND SPINDLE ASSEMBLY TODRIVE PULLEYThe auxiliary abrasive drum and spindle assembly isfurnished as standard equipmen

Page 16 - • DELTA)

ASSEMBLING AUXILIARY END TABLEASSEMBLYThe auxiliary end table is furnished as standard equip-ment with the edge sander. The table is used whenperformi

Comments to this Manuals

No comments