Delta 36-650 Instruction Manual download pdf (Page 3)

17. REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure switch is in “OFF” position before plugging in

power cord.

In the event of a power failure, move switch

to the “OFF” position.

18. NEVER STAND ON TOOL. Serious injury could occur

if the tool is tipped or if the cutting tool is accidentally

contacted.

19. CHECK DAMAGED PARTS. Before further use of the

tool, a guard or other part that is damaged should be

carefully checked to ensure that it will operate properly and

perform its intended function – check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its

operation. A guard or other part that is damaged should be

properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into a blade or

cutter against the direction of rotation of the blade or cutter

only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool until it comes to a

complete stop.

22.

STAY ALERT, WATCH WHAT YOU ARE DOING, AND

USE COMMON SENSE WHEN OPERATING A POWER

TOOL. DO NOT USE TOOL WHILE TIRED OR UNDER

THE INFLUENCE OF DRUGS, ALCOHOL, OR

MEDICATION. A moment of inattention while operating

power tools may result in serious personal injury.

23. MAKE SURE TOOL IS DISCONNECTED FROM

POWER SUPPLY while motor is being mounted,

connected or reconnected.

24. THE DUST GENERATED by certain woods and wood

products can be injurious to your health. Always operate

machinery in well ventilated areas and provide for proper

dust removal. Use wood dust collection systems whenever

possible.

ADDITIONAL SAFETY RULES FOR

TABLE SAWS

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1. DO NOT OPERATE THIS MACHINE until it is

assembled and installed according to the

instructions.

2. OBTAIN ADVICE FROM YOUR SUPERVISOR,

instructor, or another qualified person if you are

not familiar with the operation of this machine.

3. FOLLOW ALL WIRING CODES and recommended

electrical connections.

4. USE THE GUARDS WHENEVER POSSIBLE.

Check to see that they are in place, secured, and

working correctly.

5. AVOID KICKBACK by:

A. keeping blade sharp and free of rust and pitch.

B. keeping rip fence parallel to the saw blade.

C. using saw blade guard and spreader for every

possible operation, including all through

sawing.

D. pushing the workpiece past the saw blade prior

to release.

E. never ripping a workpiece that is twisted or

warped, or does not have a straight edge to

guide along the fence.

F. using featherboards when the anti-kickback

device cannot be used.

G. never sawing a large workpiece that cannot be

controlled.

H. never using the fence as a guide when

crosscutting.

I. never sawing a workpiece with loose knots or

other flaws.

6. ALWAYS USE GUARDS, SPLITTER, AND ANTI-

KICKBACK FINGERS except when otherwise

directed in the manual.

7. REMOVE CUT-OFF PIECES AND SCRAPS from

the table before starting the saw. The vibration of the

machine may cause them to move into the saw

blade and be thrown out. After cutting, turn the

machine off. When the blade has come to a

complete stop, remove all debris.

8. NEVER START THE MACHINE with the workpiece

against the blade.

9. HOLD THE WORKPIECE FIRMLY against the miter

gauge or fence.

10. NEVER run the workpiece between the fence and a

moulding cutterhead.

11. NEVER perform “free-hand” operations. Use either

the fence or miter gauge to position and guide the

workpiece.

12. USE PUSH STICK(S) for ripping a narrow

workpiece.

13. AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause a

hand to move into the blade.

14. KEEP ARMS, HANDS, AND FINGERS away from

the blade.

15. NEVER have any part of your body in line with the

path of the saw blade.

16. NEVER REACH AROUND or over the saw blade.

17. NEVER attempt to free a stalled saw blade without

first turning the machine “OFF”.

18. PROPERLY SUPPORT LONG OR WIDE

workpieces.

19. NEVER PERFORM LAYOUT, assembly or set-up

work on the table/work area when the machine is

running.

20. TURN THE MACHINE “OFF” AND DISCONNECT

THE MACHINE from the power source before

installing or removing accessories, before adjusting

or changing set-ups, or when making repairs.

21. TURN THE MACHINE “OFF”, disconnect the

machine from the power source, and clean the

table/work area before leaving the machine. LOCK

THE SWITCH IN THE “OFF” POSITION to prevent

unauthorized use.

22. ADDITIONAL INFORMATION regarding the safe

and proper operation of this tool is available from

the Power Tool Institute, 1300 Summer Avenue,

Cleveland, OH 44115-2851. Information is also

available from the National Safety Council, 1121

Spring Lake Drive, Itasca, IL 60143-3201. Please

refer to the American National Standards Institute

ANSI 01.1 Safety Requirements for Woodworking

Machines and the U.S. Department of Labor OSHA

1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

1 2 3 4 5 6 7 8 ... 31 32

Comments to this Manuals

No comments

Delta 36-650 Instruction Manual Page 3

Comments to this Manuals

Related products and manuals for Power tools Delta 36-650