Delta 43-420 Instruction Manual

Browse online or download Instruction Manual for Power tools Delta 43-420. Delta 43-420 Instruction manual [en] User Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - Heavy-Duty Wood Shaper

INSTRUCTION MANUALDATED 9-17-99 PART NO. 432-02-651-0012©Delta International Machinery Corp. 1999Platinum Edition 2-SpeedHeavy-Duty Wood Shaper(Model

Page 2 - TABLE OF CONTENTS

10Fig. 14Fig. 16Fig. 17Fig. 18ASSEMBLING FENCETO SHAPER TABLE1. The fence on this shaper can be mounted parallelto the miter gage slot using two holes

Page 3 - SAFETY RULES

11Fig. 19Fig. 20Fig. 21Fig. 23Fig. 225. Fig. 19, illustrates fence body (C) fastened to thetable with the two fence locking handles (F).6. Loosen lock

Page 4

12Fig. 24Fig. 25Fig. 26Fig. 27 Fig. 28ASSEMBLING GUARDSTO FENCE BODY1. Assemble guard bracket (A) Fig. 24, and hex rod (B)to upright hex shaft (C) as

Page 5 - UNPACKING AND CLEANING

13Fig. 29Fig. 30Fig. 316. Fig. 29, illustrates complete fence and guard assemblymounted in the alternate position, 90 degrees to mitergage slot.ASSEMB

Page 6

14Fig. 34Fig. 36 Fig. 37Fig. 35ASSEMBLINGTABLE INSERTSThree table inserts are provided for various size cutters,as shown in Fig. 34. The large insert

Page 7

15Fig. 38Fig. 39Fig. 40ASSEMBLING SPINDLE GUARDA 4-1/2 diameter spindle guard is supplied as standard equipment and is supplied with a 1/2 bushing whi

Page 8 - ASSEMBLY INSTRUCTIONS

16CONNECTING SHAPER TO POWER SOURCEGROUNDING INSTRUCTIONSCAUTION: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATORFROM ELECTRIC SHOCK.I

Page 9 - AND ON/OFF SWITCH

17STARTING AND STOPPING THE SHAPERTo apply power to the machine, push “ON” button (A) Fig. 43. To stop the machine, push“OFF” button (B).LOCKING SWITC

Page 10 - TO SHAPER TABLE

18Fig. 45Fig. 46Fig. 47RAISING ANDLOWERING SPINDLEThe spindle can be raised or lowered by loosening lockknob (A) Fig. 45, and turning handwheel (B). T

Page 11

19FENCE CONTROLS AND ADJUSTMENTSFig. 50 Fig. 51Fig. 491. DISCONNECT SHAPER FROM POWER SOURCE. IMPORTANT: The fence halves (A) Fig. 48, should beadjust

Page 12 - TO FENCE BODY

2TABLE OF CONTENTSSAFETY RULES ...

Page 13 - CHANGING SPINDLES

20Fig. 53Fig. 54Fig. 55Fig. 52GUARD CONTROLSAND ADJUSTMENTSDISCONNECT SHAPER FROM POWER SOURCE.The spring clamp (A) Fig. 52, holddown (B), and clearpl

Page 14 - ASSEMBLING

21Fig. 564. Loosen thumb screws on guard mounting bracket (P)Fig. 56, and adjust spring clamp (N) so it will provideinward pressure on workpiece; then

Page 15 - ASSEMBLING SPINDLE GUARD

22SHAPING WITH COLLARS AND STARTING PINWhen shaping with collars and starting pin, the following rules must always be followed for good workand safety

Page 16 - SINGLE PHASE OPERATION

23Fig. 67 Fig. 68Fig. 69Fig. 70Fig. 71STARTING PIN1. Your machine is supplied with a tapered starting pin(A) Fig. 67, which is used as a support when

Page 17

24Delta Shaper AccessoriesHigh-Speed Steel3-Lip Shaper CuttersAll have 1/2spindle hole. Involute relief designpermits honing of the face without chang

Page 18

25Delta Shaper Accessories (continued)Door Edge DetailAll 215/16diameter.3/4bore, 1/2T-Bushing.Bead or Half Round ConcaveAll 215/16diameter.3/4bore,

Page 19

26Delta Shaper Accessories (continued)Male and Female SashAll 215/16diameter.3/4bore with 1/2T-Bushing.Drawer JointAll 215/16diameter.3/4bore, 1/2T-

Page 20 - AND ADJUSTMENTS

27Delta Shaper Accessories (continued)Double Sided 8-Cutter Cope and Pattern SetIncludes 1/4and 1/2wide x 5/8tongue andgroove cutters. All 215/16dia

Page 21 - OPERATIONS

28Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, ormachine accessory which in normal use has proven

Page 22 - POSITION OF COLLARS

3SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certainhazards in

Page 23 - REPLACING SPINDLE CARTRIDGE

4ADDITIONAL SAFETY RULES FOR WOOD SHAPERS1. WARNING: DO NOT OPERATE YOUR WOODSHAPER UNTIL IT IS COMPLETELY ASSEMBLED ANDINSTALLED ACCORDING TO THE INS

Page 24 - Delta Shaper Accessories

5UNPACKING AND CLEANINGCarefully unpack the shaper and fence system from the shipping containers. Clean all loose parts and removethe protective coati

Page 25

64. 10 Wide Cast Iron Extension Wings5. Wrenches (2)6. 7/16-20 x 1 Hex Cap Screws (6) for mountingextension wings7. Flat Washers (6) for mounting exte

Page 26 - T-Bushing

727. Fence Body28. Left and Right fence halves29. Locking Levers (2) for fence halves30. Flat Washers (2) for locking levers31. Spring clamp for fence

Page 27

ASSEMBLY INSTRUCTIONSWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE SHAPER TO THE POWER SOURCEUNTIL THE SHAPER IS COMPLETELY ASSEMBLED AND YOU HAVE

Page 28 - Two Year Limited Warranty

9Fig. 9 Fig. 10Fig. 11Fig. 13Fig. 12ASSEMBLINGSWITCH BRACKETAND ON/OFF SWITCH1. The on/off switch (A) Fig. 9, and switch mountingbracket (B) are shipp

Comments to this Manuals

No comments