Delta BS220LS Instruction Manual

Browse online or download Instruction Manual for Power tools Delta BS220LS. Delta BS220LS Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 21
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
INSTRUCTION MANUAL
12" Band Saw
(Model BS220LS)
PART NO. 909507 - 12-23-02
Copyright © 2002 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
ESPAÑOL: PÁGINA 21
Page view 0
1 2 3 4 5 6 ... 20 21

Summary of Contents

Page 1 - 12" Band Saw

INSTRUCTION MANUAL12" Band Saw(Model BS220LS)PART NO. 909507 - 12-23-02Copyright © 2002 Delta MachineryTo learn more about DELTA MACHINERY visit

Page 2 - GENERAL SAFETY RULES

10OPENING AND CLOSINGHINGED DOORWhen making adjustments such as changing the blade,tracking the blade, blade guide adjustments, etc., thehinged doors

Page 3 - SAVE THESE INSTRUCTIONS

11TRACKING THE BLADEFor accurate work and maximum blade life, it isimportant that the blade (A) Fig. 18, be centered on theupper band saw wheel. When

Page 4 - GROUNDING INSTRUCTIONS

12ADJUSTING UPPER BLADEGUIDES AND BLADESUPPORT BEARINGFig. 21Fig. 22JHGAGBFCDEThe blade guides must be properly adjusted to preventthe blade from twis

Page 5 - OPERATING INSTRUCTIONS

13Fig. 24DDFE2. The lower blade guides are held in the guide bracketwith set screws (D) Fig. 24. Loosen set screws (D) andadjust blade guides as close

Page 6 - BAND SAW PARTS

14ADJUSTING BELT TENSIONIf the drive belt on your band saw is slipping, check andadjust as follows:DISCONNECT MACHINE FROM POWERSOURCE.1. Remove screw

Page 7 - ASSEMBLY

15DUST CHUTEA dust chute (A) Fig. 33, is provided which enables youto connect your band saw to a standard shop vacuum ordust collector. The opening of

Page 8

16TROUBLESHOOTING GUIDEIn spite of how well a band saw is maintained, problems can occur. The following troubleshootingguide will help you solve the m

Page 9

17TROUBLESHOOTING GUIDE(CONTINUED)Trouble: BLADE WILL NOT TRACK.Probable Cause Remedy1. Blade too loose 1. Adjust tension2. Upper wheel not properly a

Page 10 - BLADE TENSION

BAND SAW BLADESA band saw blade is a delicate piece of steel that is subjected to tremendous strain. You canobtain long use from a band saw blade if y

Page 12

2Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards involved with

Page 13 - TILTING THE TABLE

20Printed in U.S.A.Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machin

Page 14 - MAINTENANCE

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

Page 15 - OPERATING THE BAND SAW

317. REDUCE THE RISK OF UNINTENTIONAL STARTING.Make sure switch is in “OFF” position before plugging inpower cord. In the event of a power failure, mo

Page 16 - TROUBLESHOOTING GUIDE

4POWER CONNECTIONSA separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected

Page 17

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding type plug a

Page 18 - BAND SAW BLADES

6BAND SAW PARTSFig. 2123456789101. Band Saw2. 12¾" Upper Brace (2)3. 21½" Upper Brace (2)4. 17" Lower Brace (2)5. 25¾" Lower Brace

Page 19

ASSEMBLYFOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE E

Page 20 - ACCESSORIES

83. Place a M8.4 flat washer onto a M8x1.25x45mm hexhead screw. Insert the screw through the hole (D) Fig. 6,in the stand and thread screw into the ta

Page 21 - • DELTA)

94. Place a M6.4 flat washer (B) Fig. 10, onto aM6x1x30mm cheese head screw (A), and insert screwslot in table. Thread a M6x1 wing nut (C) Fig. 10, on

Comments to this Manuals

No comments