Delta DP300 Instruction Manual

Browse online or download Instruction Manual for Power tools Delta DP300. Delta DP300 Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 17
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
INSTRUCTION MANUAL
12" Bench Drill Press
(Model DP300)
ESPAÑOL: PÁGINA 17
PART NO. 905575-04-29-04
Copyright © 2004 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
62061
RTD10000126AA
Page view 0
1 2 3 4 5 6 ... 16 17

Summary of Contents

Page 1 - 12" Bench Drill Press

INSTRUCTION MANUAL12" Bench Drill Press(Model DP300)ESPAÑOL: PÁGINA 17PART NO. 905575-04-29-04Copyright © 2004 Delta MachineryTo learn more about

Page 2 - GENERAL SAFETY RULES

10NOTE: Make certain that the spindle taper (Q) Fig. 17 and the tapered hole in the chuck (R) are clean and free ofgrease, lacquer, or rust preventive

Page 3

11FASTENING DRILL PRESS TOSUPPORTING SURFACEIf, during operation, the machine has a tendency to tipover, slide, or walk on the supporting surface, sec

Page 4 - SAVE THESE INSTRUCTIONS

123. The table can be tilted right or left by removing thetable alignment pin (C) Fig. 25.NOTE: If the pin (C) is difficult to remove, turn the nut (E

Page 5 - GROUNDING INSTRUCTIONS

13SPINDLE MOTOR3100234017201100620SPINDLE SPEEDSFive spindle speeds (620, 1100, 1720, 2340, and 3100 RPM) are available with your drill press. See the

Page 6 - UNPACKING AND CLEANING

14The use of accessories and attachments not recommended by Delta may result in risk of injury.IMPORTANT: When the workpiece (A) Fig. 33 is longenough

Page 7 - CARTON CONTENTS

15INSTALLING AND REMOVING DRILL BITSNOTE: Use drill bits with a shank of 1/2" or less in diameter.Fig. 34DISCONNECT MACHINE FROM POWER SOURCE.1.

Page 8 - ASSEMBLY

16PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

Page 9

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE •DELTA S.A.) (Les marquessuivantes sont des

Page 10

2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

Page 11

3GENERAL SAFETY RULES1. FOR YOUR OWN SAFETY, READ THE INSTRUCTIONMANUAL BEFORE OPERATING THE MACHINE.Learning the machine’s application, limitations,

Page 12 - TABLE ADJUSTMENTS

4ADDITIONAL SAFETY RULES FORFOR DRILL PRESSES1. DO NOT OPERATE THIS MACHINE until it iscompletely assembled and installed according tothe instructions

Page 13 - DRILLING HOLES TO DEPTH

5A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

Page 14 - OPERATION

6EXTENSION CORDSUse proper extension cords. Make sureyour extension cord is in good condition and is a 3-wireextension cord which has a 3-prong ground

Page 15 - DRILLING METAL

714. Clamp15. Mounting bracket16. Tray17. Mounting arm1. Drill Press Head and Motor 2. Table3. Column, Base Flange and Rack4. Base5. M8x1.25x25mm Hex

Page 16 - ACCESSORIES

81. Attach the column (A) Fig. 3 to the base (B) using the four M8x1.25x25mm hex head screws (C), three of whichare shown. Loosen the set screw (D) an

Page 17 - • DELTA)

9Fig. 8Fig. 11Fig. 125. Place the mounting bracket (A) Fig. 9 on the column.NOTE: To avoid interference with the spindle height adjusting handles (P)

Comments to this Manuals

No comments