Delta AH500 series Manual Page 274
- Page / 297
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
AH500 Hardware Manual
9.1.3
BUS FAULT LED Indicator’s Being ON
When a CPU module detects an error, the BUS FAULT LED indicator on the CPU module is ON. The BUS
FAULT LED indicator on the CPU module corresponds to the ERROR LED indicator on an I/O module. If an
error occurs in an I/O module, the status of the BUS FAULT LED indicator on the CPU module is the same as
that of the ERROR LED indicator on the I/O module. If there are errors occurring in the I/O modules, the BUS
FAULT LED indicator on the CPU module will be ON. For example, the BUS FAULT LED indicator on the CPU
module will be ON if the ERROR LED indicator on I/O module A is ON and the ERROR LED indicator on I/O
module B blinks. If the ERROR LED indicator on I/O module B still blinks after the error occurring in I/O module
A is eliminated, the BUS FAULT LED indicator on the CPU module will blink. Please refer to sections
12.4.2~12.4.8 in AH500 Operation Manual for more information about the LED indicators.
Users can get the remedies for the errors detected by a CPU module from the table below. If the error code
which users get is not listed in the table below, users need to check whether the I/O module operates normally.
Please refer to section 9.2 in this manual for more information about the troubleshooting for I/O modules.
Error
code
Description Remedy
16#0013
The I/O module can not run/stop.
(SM10)
Check whether the setting of the parameter for the
module is correct. If the setting is correct, please check
whether the module breaks down. If the error still occurs,
please contact the factory.
16#0014
The procedure of restoring the
system can not be executed.
(SM9)
The contents of the system backup file are incorrect, or
the file does not exist in the path specified. If the file
exists and the procedure of restoring the system can not
be executed, please backing up the system again. If the
error still occurs, please contact the factory. (Please refer
to section 7.5 in AH500 Operation Manual, and section
18.2 in ISPSoft User Manual for more information about
the memory card.)
16#1400
An error occurs when the data is
accessed through the auxiliary
processor. (SM9)
Please contact the factory.
16#1401
An error occurs when the data in
the I/O module is accessed.
(SM9)
Please contact the factory.
16#1402
The actual arrangement of the I/O
modules is not consistent with the
module table. (SM9)
Check whether the module table in HWCONFIG is
consistent with the actual arrangement of the I/O
modules.
16#1403
An error occurs when the data is
read from the module. (SM9)
Check whether the module operates normally. If the error
still occurs, please contact the factory.
16#1404
A watchdog timer error occurs in
the module. (SM9)
Check whether the module breaks down. If the module
breaks down, please replace it and contact the factory.
16#1405
The setting parameter of the
module is not found. (SM9)
Set the parameter in HWCONFIG again, and download it.
16#1406
A communication error occurs
when the data is accessed
through the main processor.
(SM9)
Check whether there is noise, and eliminate the noise. If
the error still occurs, please contact the factory.
16#1407
A communication error occurs
when the data is accessed
through the auxiliary processor.
(SM9)
Check whether there is noise, and eliminate the noise. If
the error still occurs, please contact the factory.
16#1408
The communication with the
module is incorrect. (SM9)
Check whether there is noise, and eliminate the noise. If
the error still occurs, please contact the factory.
9-10
- Hardware Manual 1
- Hardware Manual 1
- Table of Contents 11
- 1.1 Overview 12
- 1.2 Characteristics 18
- CPU530-RS2 21
- Main backplane 28
- Power supply module 29
- 29
- CPU module 29
- Communication cable 30
- 2.1.1.2 Accessories 30
- Extension module 30
- Extension backplane 34
- Main backplane as a RTU 34
- 2.2 Warning 35
- 2.3 Installation 36
- Installing a DIN rail 37
- Removing a DIN rail 38
- 2.3.3 Installing a Module 39
- Installation 40
- Removal 40
- 2.3.6 Connecting Backplanes 42
- Main backplan 43
- Extension backplane 43
- 3.1 General Specifications 46
- 3.2.2 Profiles 48
- 3.2.3 Dimensions 49
- CPU530-EN 50
- 3.3.2 Profiles 51
- 3.3.3 Dimensions 53
- 3.4.2 Profile 56
- 3.4.3 Dimensions 57
- 120/240 V AC 60
- 0.5 A/output 60
- (2 A/COM) 60
- 3.5.2 Profiles 62
- 24VDC 5mA 63
- 12~24VDC 0.1A 64
- 39 4039 40 67
- 12~24VDC 0.5A 69
- 32A 02NP 70
- 64AM 10N 71
- 98110 11 12 13 14 5 74
- DVPAETB-OT32B 80
- GND +24V 81
- GND +24V 82
- Analog-to-digital 84
- Digital-to-analog 88
- 3.6.2 Profiles 89
- 3.6.3 Dimensions 90
- -10~+10V 91
- -20~+20mA 91
- ±10V,±20mA 92
- ±10V,0/4~20mA 92
- 3.7.2 Profiles 94
- 3.7.3 Dimensions 96
- RTD 2/3/4-WIRE 97
- 3.8.2 Profiles 101
- Ethernet 102
- Points for attention: 103
- Profibus 104
- 1. PROFIBUS-DP port 105
- NODE ADDRESS 107
- 3.8.3 Dimensions 108
- Et hern et 109
- Node Address 110
- 3.9.2 Profiles 124
- Micro SD 127
- 20MC20MC 129
- 3.9.3 Dimensions 131
- 3.10.2 Profiles 141
- 3.10.3 Dimensions 143
- NodeAddress 144
- 3.11.2 Profiles 145
- AHAADP01EF-5A 146
- AHAADP02EF-5A 146
- 4.1 Assigning I/O Addresses 150
- 4.3 User-defined Addresses 154
- AH500 Hardware Manual 158
- Chapter 5 Wiring 159
- 5.1 Wiring 161
- 5.2 Connecting Power Cables 162
- AC power supply 163
- 100-240V 163
- 100~240V 164
- AHPS05-5A 165
- 5.2.4 Power Consumption 166
- 5.3 Wiring CPU Modules 168
- 5.4.1 Wiring AH16AM10N-5A 169
- 5.4.2 Wiring AH16AM30N-5A 170
- 5.4.3 Wiring AH16AR10N-5A 171
- 5.4.4 Wiring AH16AN01S-5A 172
- 5.4.5 Wiring AH16AN01R-5A 173
- 5.4.6 Wiring AH16AN01T-5A 174
- 5.4.7 Wiring AH16AN01P-5A 175
- 5.4.8 Wiring AH16AP11R-5A 176
- 5.4.9 Wiring AH16AP11T-5A 177
- 5.4.10 Wiring AH16AP11P-5A 178
- 5.4.11 Wiring AH32AM10N-5A 179
- 5.4.12 Wiring AH32AM10N-5B 180
- 5.4.13 Wiring AH32AM10N-5C 181
- 5.4.14 Wiring AH32AN02T-5A 182
- 5.4.15 Wiring AH32AN02T-5B 183
- 5.4.16 Wiring AH32AN02T-5C 184
- 5.4.17 Wiring AH32AN02P-5A 186
- 5.4.18 Wiring AH32AN02P-5B 187
- 5.4.19 Wiring AH32AN02P-5C 188
- 5.4.20 Wiring AH64AM10N-5C 190
- 5.4.21 Wiring AH64AN02T-5C 191
- 5.4.22 Wiring AH64AN02P-5C 192
- 5.5.1.2 Relay Type 194
- Sinking 194
- Two-wire proximit 195
- Optoelectronic switch 196
- 5.5.2.1 Output Circuits 197
- Contact Current(A) 198
- DC power supply 200
- D: 1N4001 diode 200
- 5.6.1 Wiring AH04AD-5A 203
- 5.6.2 Wiring AH08AD-5B 204
- 5.6.3 Wiring AH08AD-5C 204
- 5.6.4 Wiring AH04DA-5A 205
- 5.6.5 Wiring AH08DA-5B 206
- 5.6.6 Wiring AH08DA-5C 207
- 5.6.7 Wiring AH06XA-5A 208
- 5.7.1 Wiring AH04PT-5A 209
- 5.7.2 Wiring AH08PTG-5A 210
- 5.8 Wiring Network Modules 211
- Shielded cabl 212
- 5.8.2 Wiring AH10EN-5A 213
- 5.8.3 Wiring AH10SCM-5A 213
- DP Port 214
- Function Switch 216
- 5.9.1 Wiring AHRTU-DNET-5A 216
- 5.9.2 Wiring AHRTU-PFBS-5A 218
- 5.10.3.1 External Wiring 235
- Encoder output 236
- H04HC-5A high-speed input 236
- Transistor output 237
- AH04HC-5A 237
- Terminals on AH05PM-5A 238
- Connector on AH10PM-5A 239
- Connector on AH15PM-5A 240
- Sinking 241
- Sourcing 241
- (24 V sinking) 242
- AC servo drive 244
- Chapter 5 Wiring 246
- 5.10.5 Wiring AH20MC-5A 250
- Chapter 6 Memory Card 253
- SD card families 254
- AHCPU500/510/520/530-RS2 255
- AHCPU500/510/520/530-EN 255
- Write-protected 255
- Chapter 7 EMC Standards 257
- 7.1.3 Cables 259
- 8.1 Cautions 262
- 8.2 Daily Maintenance 262
- 8.3 Periodic Maintenance 263
- Chapter 9 Troubleshooting 265
- Measurement Modules 285
- 1. AH10PFBS-5A has not 295
- 2. PROFIBUS-DP master 295
- Chapter 9 Troubleshooting 297
Related products and manuals for Recording Equipment Delta AH500 series
(32 pages)
(42 pages)© 2020, manymanuals.com. All rights reserved. | 3.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals