Delta AH500 series Manual Page 275
- Page / 297
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 9 Troubleshooting
9-11
Error
code
Description Remedy
16#1409
The extension backplane is
disconnected. (SM9)
1. Check whether the extension backplane is connected
properly.
2. Check whether the extension backplane operates
normally, and make sure that the extension backplane
is not affected by noise.
16#140A
The communication with the
extension backplane is incorrect.
(SM9)
1. Check whether the extension backplane is connected
properly.
2. Check whether the extension backplane operates
normally, and make sure that the extension backplane
is not affected by noise.
16#140B
The number of network modules
exceeds the limit. (SM9)
Please decrease the number of network modules to the
number supported by the system.
9.1.4
BUS FAULT LED Indicator’s Blinking
If the BUS FAULT LED blinks, please check the operating state of the module. Please refer to sections
12.4.2~12.4.8 in AH500 Operation Manual for more information about the LED indicators, and section 9.2 in
this manual for more information about the troubleshooting for I/O modules.
9.1.5
Others
Error
code
Description Remedy
16#000F
The original program in the PLC is
damaged.
After users compile the program again, they can
download the program again.
16#2026
The interrupt number used in RS is
incorrect.
Compile the program again, and download the program
again. If the error still occurs, please contact the factory.
16#600A TCP connection failure (SM1090)
1. Check the actual network configuration, and check
whether the number of TCP connections exceeds the
upper limit supported by the CPU module.
2. Retry the TCP connection later. (This error does not
cause the PLC to stop running. Users can perform the
corresponding remedy by means of the related flag in
the program.)
16#600B UDP connection failure (SM1091)
1. Check the actual network configuration, and check
whether the number of UDP connections exceeds the
upper limit supported by the CPU module.
2. Retry the TCP connection later. (This error does not
cause the PLC to stop running. Users can perform the
corresponding remedy by means of the related flag in
the program.)
16#600C
The TCP socket has been used.
(SM1109)
1. Check whether the actual data access results in the
use of the same socket.
2. Change the socket number, or retry the socket later.
(This error does not cause the PLC to stop running.
Users can perform the corresponding remedy by
means of the related flag in the program.)
16#600D The RJ45 port is not connected. Check the communication cable.
16#6100
The email connection is busy.
(SM1113)
Retry the email connection later. (This error does not
cause the PLC to stop running. Users can perform the
corresponding remedy by means of the related flag in
the program.)
16#6104
The attachment in the email does
not exist. (SM1113)
Check whether the attachment exists in the memory
card.
- Hardware Manual 1
- Hardware Manual 1
- Table of Contents 11
- 1.1 Overview 12
- 1.2 Characteristics 18
- CPU530-RS2 21
- Main backplane 28
- Power supply module 29
- 29
- CPU module 29
- Communication cable 30
- 2.1.1.2 Accessories 30
- Extension module 30
- Extension backplane 34
- Main backplane as a RTU 34
- 2.2 Warning 35
- 2.3 Installation 36
- Installing a DIN rail 37
- Removing a DIN rail 38
- 2.3.3 Installing a Module 39
- Installation 40
- Removal 40
- 2.3.6 Connecting Backplanes 42
- Main backplan 43
- Extension backplane 43
- 3.1 General Specifications 46
- 3.2.2 Profiles 48
- 3.2.3 Dimensions 49
- CPU530-EN 50
- 3.3.2 Profiles 51
- 3.3.3 Dimensions 53
- 3.4.2 Profile 56
- 3.4.3 Dimensions 57
- 120/240 V AC 60
- 0.5 A/output 60
- (2 A/COM) 60
- 3.5.2 Profiles 62
- 24VDC 5mA 63
- 12~24VDC 0.1A 64
- 39 4039 40 67
- 12~24VDC 0.5A 69
- 32A 02NP 70
- 64AM 10N 71
- 98110 11 12 13 14 5 74
- DVPAETB-OT32B 80
- GND +24V 81
- GND +24V 82
- Analog-to-digital 84
- Digital-to-analog 88
- 3.6.2 Profiles 89
- 3.6.3 Dimensions 90
- -10~+10V 91
- -20~+20mA 91
- ±10V,±20mA 92
- ±10V,0/4~20mA 92
- 3.7.2 Profiles 94
- 3.7.3 Dimensions 96
- RTD 2/3/4-WIRE 97
- 3.8.2 Profiles 101
- Ethernet 102
- Points for attention: 103
- Profibus 104
- 1. PROFIBUS-DP port 105
- NODE ADDRESS 107
- 3.8.3 Dimensions 108
- Et hern et 109
- Node Address 110
- 3.9.2 Profiles 124
- Micro SD 127
- 20MC20MC 129
- 3.9.3 Dimensions 131
- 3.10.2 Profiles 141
- 3.10.3 Dimensions 143
- NodeAddress 144
- 3.11.2 Profiles 145
- AHAADP01EF-5A 146
- AHAADP02EF-5A 146
- 4.1 Assigning I/O Addresses 150
- 4.3 User-defined Addresses 154
- AH500 Hardware Manual 158
- Chapter 5 Wiring 159
- 5.1 Wiring 161
- 5.2 Connecting Power Cables 162
- AC power supply 163
- 100-240V 163
- 100~240V 164
- AHPS05-5A 165
- 5.2.4 Power Consumption 166
- 5.3 Wiring CPU Modules 168
- 5.4.1 Wiring AH16AM10N-5A 169
- 5.4.2 Wiring AH16AM30N-5A 170
- 5.4.3 Wiring AH16AR10N-5A 171
- 5.4.4 Wiring AH16AN01S-5A 172
- 5.4.5 Wiring AH16AN01R-5A 173
- 5.4.6 Wiring AH16AN01T-5A 174
- 5.4.7 Wiring AH16AN01P-5A 175
- 5.4.8 Wiring AH16AP11R-5A 176
- 5.4.9 Wiring AH16AP11T-5A 177
- 5.4.10 Wiring AH16AP11P-5A 178
- 5.4.11 Wiring AH32AM10N-5A 179
- 5.4.12 Wiring AH32AM10N-5B 180
- 5.4.13 Wiring AH32AM10N-5C 181
- 5.4.14 Wiring AH32AN02T-5A 182
- 5.4.15 Wiring AH32AN02T-5B 183
- 5.4.16 Wiring AH32AN02T-5C 184
- 5.4.17 Wiring AH32AN02P-5A 186
- 5.4.18 Wiring AH32AN02P-5B 187
- 5.4.19 Wiring AH32AN02P-5C 188
- 5.4.20 Wiring AH64AM10N-5C 190
- 5.4.21 Wiring AH64AN02T-5C 191
- 5.4.22 Wiring AH64AN02P-5C 192
- 5.5.1.2 Relay Type 194
- Sinking 194
- Two-wire proximit 195
- Optoelectronic switch 196
- 5.5.2.1 Output Circuits 197
- Contact Current(A) 198
- DC power supply 200
- D: 1N4001 diode 200
- 5.6.1 Wiring AH04AD-5A 203
- 5.6.2 Wiring AH08AD-5B 204
- 5.6.3 Wiring AH08AD-5C 204
- 5.6.4 Wiring AH04DA-5A 205
- 5.6.5 Wiring AH08DA-5B 206
- 5.6.6 Wiring AH08DA-5C 207
- 5.6.7 Wiring AH06XA-5A 208
- 5.7.1 Wiring AH04PT-5A 209
- 5.7.2 Wiring AH08PTG-5A 210
- 5.8 Wiring Network Modules 211
- Shielded cabl 212
- 5.8.2 Wiring AH10EN-5A 213
- 5.8.3 Wiring AH10SCM-5A 213
- DP Port 214
- Function Switch 216
- 5.9.1 Wiring AHRTU-DNET-5A 216
- 5.9.2 Wiring AHRTU-PFBS-5A 218
- 5.10.3.1 External Wiring 235
- Encoder output 236
- H04HC-5A high-speed input 236
- Transistor output 237
- AH04HC-5A 237
- Terminals on AH05PM-5A 238
- Connector on AH10PM-5A 239
- Connector on AH15PM-5A 240
- Sinking 241
- Sourcing 241
- (24 V sinking) 242
- AC servo drive 244
- Chapter 5 Wiring 246
- 5.10.5 Wiring AH20MC-5A 250
- Chapter 6 Memory Card 253
- SD card families 254
- AHCPU500/510/520/530-RS2 255
- AHCPU500/510/520/530-EN 255
- Write-protected 255
- Chapter 7 EMC Standards 257
- 7.1.3 Cables 259
- 8.1 Cautions 262
- 8.2 Daily Maintenance 262
- 8.3 Periodic Maintenance 263
- Chapter 9 Troubleshooting 265
- Measurement Modules 285
- 1. AH10PFBS-5A has not 295
- 2. PROFIBUS-DP master 295
- Chapter 9 Troubleshooting 297
Related products and manuals for Recording Equipment Delta AH500 series
(32 pages)
(42 pages)© 2020, manymanuals.com. All rights reserved. | 0.794 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals