Delta AH500 series Manual Page 285
- Page / 297
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 9 Troubleshooting
9-21
Error
code
Description Remedy
16#9A5B
There is no response from slave
27 in the PLC Link. (SM1592)
1. Check the communication setting in the master, and
the communication setting in slave 27.
2. Check the communication cable.
16#9A5C
There is no response from slave
28 in the PLC Link. (SM1592)
1. Check the communication setting in the master, and
the communication setting in slave 28.
2. Check the communication cable.
16#9A5D
There is no response from slave
29 in the PLC Link. (SM1592)
1. Check the communication setting in the master, and
the communication setting in slave 29.
2. Check the communication cable.
16#9A5E
There is no response from slave
30 in the PLC Link. (SM1592)
1. Check the communication setting in the master, and
the communication setting in slave 30.
2. Check the communication cable.
16#9A5F
There is no response from slave
31 in the PLC Link. (SM1592)
1. Check the communication setting in the master, and
the communication setting in slave 31.
2. Check the communication cable.
16#9A60
There is no response from slave
32 in the PLC Link. (SM1592)
1. Check the communication setting in the master, and
the communication setting in slave 32.
2. Check the communication cable.
16#9A61
The setting of the PLC Link mode
is incorrect. (SM1589)
Make sure that SM1586 and SM1587 are not both ON.
16#9A62
The number of polling cycles in the
PLC Link is incorrect. (SM1592)
If the PLC Link is in the manual mode, please make sure
that the number of polling cycles is within the range
between 1 and 65535.
16#9A63
There is a handshaking timeout
when the CPU module establishes
a connection with the network
module. (SM1596)
Check whether the network module operates normally.
16#9A64
There is no network module
parameter in the CPU module.
(SM1596)
Download the parameter in HWCONFIG again.
9.2
Troubleshooting for I/O Modules
Introduction of modules
Digital I/O modules, analog I/O modules, network modules, temperature measurement modules, and
motion control modules can be installed in an AH500 system. Please refer to AH500 Module Manual for
more information about the specifications for I/O modules. The error codes and the remedies for the errors
are listed below.
9.2.1
Troubleshooting for Analog I/O Modules and Temperature
Measurement Modules
Error
code
Description Remedy
16#A000
The signal received by channel 0
exceeds the range of inputs
which can be received by the
hardware. (The ERROR LED
indicator blinks.)
Check the module parameter in HWCONFIG.
Check whether the signal received by channel 0 exceeds
the range of inputs which can be received by the
hardware.
16#A001
The signal received by channel 1
exceeds the range of inputs
which can be received by the
hardware. (The ERROR LED
indicator blinks.)
Check the module parameter in HWCONFIG.
Check whether the signal received by channel 1 exceeds
the range of inputs which can be received by the
hardware.
- Hardware Manual 1
- Hardware Manual 1
- Table of Contents 11
- 1.1 Overview 12
- 1.2 Characteristics 18
- CPU530-RS2 21
- Main backplane 28
- Power supply module 29
- 29
- CPU module 29
- Communication cable 30
- 2.1.1.2 Accessories 30
- Extension module 30
- Extension backplane 34
- Main backplane as a RTU 34
- 2.2 Warning 35
- 2.3 Installation 36
- Installing a DIN rail 37
- Removing a DIN rail 38
- 2.3.3 Installing a Module 39
- Installation 40
- Removal 40
- 2.3.6 Connecting Backplanes 42
- Main backplan 43
- Extension backplane 43
- 3.1 General Specifications 46
- 3.2.2 Profiles 48
- 3.2.3 Dimensions 49
- CPU530-EN 50
- 3.3.2 Profiles 51
- 3.3.3 Dimensions 53
- 3.4.2 Profile 56
- 3.4.3 Dimensions 57
- 120/240 V AC 60
- 0.5 A/output 60
- (2 A/COM) 60
- 3.5.2 Profiles 62
- 24VDC 5mA 63
- 12~24VDC 0.1A 64
- 39 4039 40 67
- 12~24VDC 0.5A 69
- 32A 02NP 70
- 64AM 10N 71
- 98110 11 12 13 14 5 74
- DVPAETB-OT32B 80
- GND +24V 81
- GND +24V 82
- Analog-to-digital 84
- Digital-to-analog 88
- 3.6.2 Profiles 89
- 3.6.3 Dimensions 90
- -10~+10V 91
- -20~+20mA 91
- ±10V,±20mA 92
- ±10V,0/4~20mA 92
- 3.7.2 Profiles 94
- 3.7.3 Dimensions 96
- RTD 2/3/4-WIRE 97
- 3.8.2 Profiles 101
- Ethernet 102
- Points for attention: 103
- Profibus 104
- 1. PROFIBUS-DP port 105
- NODE ADDRESS 107
- 3.8.3 Dimensions 108
- Et hern et 109
- Node Address 110
- 3.9.2 Profiles 124
- Micro SD 127
- 20MC20MC 129
- 3.9.3 Dimensions 131
- 3.10.2 Profiles 141
- 3.10.3 Dimensions 143
- NodeAddress 144
- 3.11.2 Profiles 145
- AHAADP01EF-5A 146
- AHAADP02EF-5A 146
- 4.1 Assigning I/O Addresses 150
- 4.3 User-defined Addresses 154
- AH500 Hardware Manual 158
- Chapter 5 Wiring 159
- 5.1 Wiring 161
- 5.2 Connecting Power Cables 162
- AC power supply 163
- 100-240V 163
- 100~240V 164
- AHPS05-5A 165
- 5.2.4 Power Consumption 166
- 5.3 Wiring CPU Modules 168
- 5.4.1 Wiring AH16AM10N-5A 169
- 5.4.2 Wiring AH16AM30N-5A 170
- 5.4.3 Wiring AH16AR10N-5A 171
- 5.4.4 Wiring AH16AN01S-5A 172
- 5.4.5 Wiring AH16AN01R-5A 173
- 5.4.6 Wiring AH16AN01T-5A 174
- 5.4.7 Wiring AH16AN01P-5A 175
- 5.4.8 Wiring AH16AP11R-5A 176
- 5.4.9 Wiring AH16AP11T-5A 177
- 5.4.10 Wiring AH16AP11P-5A 178
- 5.4.11 Wiring AH32AM10N-5A 179
- 5.4.12 Wiring AH32AM10N-5B 180
- 5.4.13 Wiring AH32AM10N-5C 181
- 5.4.14 Wiring AH32AN02T-5A 182
- 5.4.15 Wiring AH32AN02T-5B 183
- 5.4.16 Wiring AH32AN02T-5C 184
- 5.4.17 Wiring AH32AN02P-5A 186
- 5.4.18 Wiring AH32AN02P-5B 187
- 5.4.19 Wiring AH32AN02P-5C 188
- 5.4.20 Wiring AH64AM10N-5C 190
- 5.4.21 Wiring AH64AN02T-5C 191
- 5.4.22 Wiring AH64AN02P-5C 192
- 5.5.1.2 Relay Type 194
- Sinking 194
- Two-wire proximit 195
- Optoelectronic switch 196
- 5.5.2.1 Output Circuits 197
- Contact Current(A) 198
- DC power supply 200
- D: 1N4001 diode 200
- 5.6.1 Wiring AH04AD-5A 203
- 5.6.2 Wiring AH08AD-5B 204
- 5.6.3 Wiring AH08AD-5C 204
- 5.6.4 Wiring AH04DA-5A 205
- 5.6.5 Wiring AH08DA-5B 206
- 5.6.6 Wiring AH08DA-5C 207
- 5.6.7 Wiring AH06XA-5A 208
- 5.7.1 Wiring AH04PT-5A 209
- 5.7.2 Wiring AH08PTG-5A 210
- 5.8 Wiring Network Modules 211
- Shielded cabl 212
- 5.8.2 Wiring AH10EN-5A 213
- 5.8.3 Wiring AH10SCM-5A 213
- DP Port 214
- Function Switch 216
- 5.9.1 Wiring AHRTU-DNET-5A 216
- 5.9.2 Wiring AHRTU-PFBS-5A 218
- 5.10.3.1 External Wiring 235
- Encoder output 236
- H04HC-5A high-speed input 236
- Transistor output 237
- AH04HC-5A 237
- Terminals on AH05PM-5A 238
- Connector on AH10PM-5A 239
- Connector on AH15PM-5A 240
- Sinking 241
- Sourcing 241
- (24 V sinking) 242
- AC servo drive 244
- Chapter 5 Wiring 246
- 5.10.5 Wiring AH20MC-5A 250
- Chapter 6 Memory Card 253
- SD card families 254
- AHCPU500/510/520/530-RS2 255
- AHCPU500/510/520/530-EN 255
- Write-protected 255
- Chapter 7 EMC Standards 257
- 7.1.3 Cables 259
- 8.1 Cautions 262
- 8.2 Daily Maintenance 262
- 8.3 Periodic Maintenance 263
- Chapter 9 Troubleshooting 265
- Measurement Modules 285
- 1. AH10PFBS-5A has not 295
- 2. PROFIBUS-DP master 295
- Chapter 9 Troubleshooting 297
Related products and manuals for Recording Equipment Delta AH500 series
(32 pages)
(42 pages)© 2020, manymanuals.com. All rights reserved. | 0.684 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals