Delta MMC120 User Manual Page 92
- Page / 150
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
92
These commands behave identical to the Open Loop ASCII command, except that the
specified stored profile information is copied into the active MODE, ACCEL, DECEL
and SPEED first. Recall that the SPEED field of the profile is not used by the Open
Loop. Refer to that command for further details.
The format of the Command Register for the Open Loop Using Profile commands is
given below:
| | 111|1111
BIT # 1234|5678|9012|3456
-------------------
HEX |SAR |CMND|INDX
VALUE -------------------
0X90 0000|XXXX|1001|0000 OPEN LOOP USING PROFILE 0
0X91 0000|XXXX|1001|0001 OPEN LOOP USING PROFILE 1
0X92 0000|XXXX|1001|0010 OPEN LOOP USING PROFILE 2
0X93 0000|XXXX|1001|0011 OPEN LOOP USING PROFILE 3
0X94 0000|XXXX|1001|0100 OPEN LOOP USING PROFILE 4
0X95 0000|XXXX|1001|0101 OPEN LOOP USING PROFILE 5
0X96 0000|XXXX|1001|0110 OPEN LOOP USING PROFILE 6
0X97 0000|XXXX|1001|0111 OPEN LOOP USING PROFILE 7
0X98 0000|XXXX|1001|1000 OPEN LOOP USING PROFILE 8
0X99 0000|XXXX|1001|1001 OPEN LOOP USING PROFILE 9
0X9A 0000|XXXX|1001|1010 OPEN LOOP USING PROFILE 10
0X9B 0000|XXXX|1001|1011 OPEN LOOP USING PROFILE 11
0X9C 0000|XXXX|1001|1100 OPEN LOOP USING PROFILE 12
0X9D 0000|XXXX|1001|1101 OPEN LOOP USING PROFILE 13
0X9E 0000|XXXX|1001|1110 OPEN LOOP USING PROFILE 14
0X9F 0000|XXXX|1001|1111 OPEN LOOP USING PROFILE 15
ThedataforthecommandOutput register represents the requested drive in millivolts.
Example
Suppose you would like to axis 0 to go into open loop at 2000mV of drive using profile
10 and axis 1 to go into open loop at 4000mV of drive using profile 11. You would send
the commands in the following format:
SAR CMND INDX (HEX)
4TTTTT+0 0000|XXXX|1001|1010 (0X9A) Issue an Open Loop using Profile
10 command
+1 2000 (07D0) Axis 1 Requested Drive
4TTTTT+2 0000|XXXX|1001|1011 (0X9B) Issue an Open Loop using Profile
11 command
+3 4000 (0FA0) Axis 2 Requested Drive
- DCS120-Win Software 1
- User Manual 1
- Table of Contents 2
- Introducing the MMC120 7
- MMC120 Overview 7
- Disclaimer 7
- Principle of Operation 9
- Starting Up the MMC120 11
- Step-by-Step MMC120 Startup 11
- Setup Details 15
- Using DCS120-Win 20
- DCS120-Win Overview 20
- Screen Layout 21
- Command area 22
- Parameter area 23
- Plot Time area 24
- Status area 24
- Status Bar 24
- Basic Topics 26
- Read-back versus Write Mode 27
- Using Popup Editors 28
- Using the STATUS Bits Window 28
- Using the Command Log 29
- Using Stored Commands 31
- Setup Options 32
- Using Multiple Motion Modules 33
- Creating a New Board File 33
- Changing Between Board Files 34
- Using Plots 37
- Selecting the Data to Plot 38
- Using the Plot Detail Window 38
- Viewing the Raw Plot Data 39
- Saving and Restoring Plots 40
- Printing a Plot 40
- Plot Time 41
- Table Editors 42
- Editing the Profile Table 44
- Editing the Event Step Table 44
- Advanced Topics 47
- Forcing Initialization 48
- Using Look-only Mode 48
- Using PC Mode 48
- Command Line Options 49
- Options Dialog Box 50
- Controller Features 51
- Event Control Overview 51
- FLASH Memory 53
- LED Indicators 54
- Motion Profiles 55
- Synchronizing Axes 57
- Two per unit 60
- Communicating with the MMC120 61
- Input Register Overview 63
- Output Register Overview 64
- 1514131211109876543210 65
- SAR Type Index 65
- Support and Troubleshooting 66
- Warranty 66
- Troubleshooting 66
- Error Handling 67
- MMC120 Module Problems 67
- Hydraulic System Problems 69
- Technical Support 73
- Parameter Errors 74
- Invalid command received 76
- Appendix A: Command Reference 78
- General ASCII Commands 78
- Start Events Command 79
- Set Feed Forward Command 79
- Go Command 79
- Halt Command 80
- Set Integral Drive Command 80
- Relative Move Command 81
- Disable Drive Output Command 81
- Set Mode Command 82
- Set Null Drive Command 82
- Open Loop Command 82
- Set Parameters Command 84
- Quit Events Command 84
- Restore Null Drive Command 84
- Save Null Drive Command 85
- Save Integral Drive Command 85
- Update FLASH Command 85
- Set Speed (Unsigned) Command 86
- Set Speed (Signed) Command 86
- Start a Graph Command 86
- Go Using Profile Commands 87
- Set Profile Commands 88
- Set Parameter Commands 90
- ASCII Commands 91
- Get Profile Commands 93
- 0xAC-0xAF 37 94
- Get Parameter Commands 95
- Event Step Edit Commands 97
- LINK TYPE/NEXT 98
- Diagnostics Command 98
- Event Step Transfer Command 99
- MODE Word Bit Map 103
- ACCELERATION 104
- DECELERATION 104
- COMMAND VALUE 105
- Command Field 106
- CONFIGURATION Word 107
- CONFIGURATION Word Bit Map 109
- SCALE Calculation Examples 111
- EXTEND LIMIT 112
- RETRACT LIMIT 113
- PROPORTIONAL GAIN 113
- INTEGRAL GAIN 114
- DIFFERENTIAL GAIN 115
- EXTEND FEED FORWARD 115
- RETRACT FEED FORWARD 116
- DEAD BAND ELIMINATOR 117
- IN POSITION 118
- FOLLOWING ERROR 118
- AUTO STOP 119
- AUTO STOP Bit Map 120
- Valid 16-Bit Positions 121
- COMMAND POSITION 122
- TARGET POSITION 123
- ACTUAL POSITION 123
- TRANSDUCER COUNTS 124
- AXIS STATUS Word 124
- STATUS Word Bit Map 128
- ACTUAL SPEED 129
- NULL DRIVE 130
- LINK VALUE 130
- Link Types and Link Values 130
- Link Next 131
- System-wide Link Types 132
- Current Axis Link Types 132
- Link Type and Link Value 133
- Selected Axis Link Types 135
- Link Type - Any Axis Speed 136
- MMC120 Specifications 138
- Appendix G: Glossary 139
- Glossary 139
Related products and manuals for Sensors Delta MMC120
Sensors Delta MMC120 User Manual
(105 pages)
(105 pages)
© 2020, manymanuals.com. All rights reserved. | 0.344 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals