Delta DT3 User Manual download pdf (Page 19)

1103H Reverse Output Bit1: output 2, Bit0: output 1

1104H Slope of Temperature Increase Unit: 0.1 /℃ min or 0.1℃/sec (refer to CommunicationAddress 1124H)

1105H Remote Input Type Selection 0: 0~20m A , 1: 4~20m A, 2: 0~5V, 3: 1~5V, 4: 0~10V

1106H AT Control 0: AT(Auto-tune), 1: ST(Self-tune)

1107H Remote Input Reverse Setting 0: forward, 1: reverse

1108H Alarm 1 Function Selection Bit3: Peak Record, Bit2: Hold Enable, Bit1: Output Reverse, Bit0: Standby Enable

1109H Alarm 2 Function Selection Bit3: Peak Record, Bit2: Hold Enable, Bit1: Output Reverse, Bit0: Standby Enable

110AH Alarm 3 Function Selection Bit3: Peak Record, Bit2: Hold Enable, Bit1: Output Reverse, Bit0: Standby Enable

110BH Alarm 1 Output Delay Time Unit: second. Setting range: 0~100sec

110CH Alarm 2 Output Delay Time Unit: second. Setting range: 0~100sec

110DH Alarm 3 Output Delay Time Unit: second. Setting range: 0~100sec

110EH Upper Limit of Control Output 1 Range: lower limit of control output ~100%, unit is 0.1%

110FH Lower Limit of Control Output 1 Range: 0~upper limit of control output, unit is 0.1%

1110H Upper Limit of Control Output 2 Range: lower limit of control output~100%, unit is 0.1%

1111H Lower Limit of Control Output 2 Range: 0~upper limit of control output, unit is 0.1%

1112H Programmable Waiting

Temeprature

Setting range: 0~1000(100.0 )℃

1113H Programmable Waiting Time Unit: min. Setting range: 0~900

1114H Programmable Slope Increase Unit: 0.1℃/min or 0.1℃/sec--- (refer to Communication Address 1124H) Setting

range: 0~1000

1115H Testing Mode

1116H Adjust Upper Limit of Analog

Linear Output 1

Adjust current: 1scale=1μA, Adjust voltage: 1scale=1mV

1117H Adjust Lower Limit of Analog

Linear Output 1

Adjust current: 1scale=1μA, Adjust voltage: 1scale=1mV

1118H Adjust Upper Limit of Analog

Linear Output 2

Adjust current: 1scale=1μA, Adjust voltage: 1scale=1mV

1119H Adjust Lower Limit of Analog

Linear Output 2

Adjust current: 1scale=1μA, Adjust voltage: 1scale=1mV

111AH Adjust Retransmission Upper

Limit

Adjust current: 1scale=1μA

111BH Adjust Retransmission Lower

Limit

Adjust current: 1scale=1μA

111CH Event 1 Selection 0: OFF, 1: Run/Stop, 2: Change SV value, 3: PID/Manual control, 4: Switch to

Programmable Hold mode

111DH Event 2 Selection 0: OFF, 1: Run/Stop, 2: Change SV value, 3: PID/Manual control, 4: Switch to

Programmable Hold mode

111EH Event 3 Selection 0: OFF, 1: Run/Stop, 2: Change SV value, 3: PID/Manual control, 4: Switch to

Programmable Hold mode

111FH PV Control Mode Selection 0: PID, 1: ON/OFF, 2: Manual control, 3: Fuzzy

1120H SV Control Mode Selection 0: Constant, 1: Slope increase, 2: Programmable input, 3: Remote Input

1121H Adjust Remote Compensation Setting range: -999~999

1122H Adjust Remote Gain Setting range: -999~999

1123H Positive/Negative Selection for

Remote

0: Positive, 1: Negative

1124H Switch Slope Time Unit 0: min, 1: sec

1125H Cold Junction Compensation 0: ON, 1: OFF

1126H Reserve the Programmable

Running Status when Power OFF

0: None, 1: Running status is saved and will continue by the previous status when

power ON.

1127H Fuzzy Gain Setting range: 1~10

1128H Fuzzy Dead Band Setting range: 0.0~PB

1129H Save Programmable Settings

into Memory

0:None, 1: Saves the programmable settings into memory

1182H CT1 Read Value Unit: 0.1A

1183H CT2 Read Value Unit: 0.1A

1. Address and Content of Bit Register: First bit of reading will put into LSB. Write data= FF00H for bit set, 0000H for bit clear.

0810H Read AT LED status 0: OFF(default), 1: ON

0811H Temperature unit display 0: , 1: / ℉℃linear input (default)

1 2 ... 14 15 16 17 18 19 20 21

Comments to this Manuals

No comments

Delta DT3 User Manual Page 19

Comments to this Manuals